571430
8
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
7
English
Read handling instructions before use.
Avoid any work exceeding
the maximum capacities.
(Rebar diameter ø 13mm.)
Do not this electric power tools
in wet wether conditions.
Do not attempt to cut two rebars
at one time.
If the switch is turned off and
then immediately turned on
again, the motor may not start.
Wait for at least one full second
before attempting to turn the
motor on again after it has been
switched off.
Begin operation only after
ensuring that there are no people
within the turning range of the
material to be bent.
Never bring your hand close to
the cutter during operation.
HOW TO USE (CUTTING)
WARNING!
Note that the unit is not a hand held tool. Be absolutely
sure to use the unit only after placing it on stable
spots such as floor, ground, etc.
Never bring your hand close to the cutter during
operation.
Never bring your hand close to the reaction stoppers
A and B during operation.
Do not cut any materials other than the rebars. If you
attempt to do so, the material can splinter into pieces
and scatter.
Only cut the one piece of rebar at a time. It is
impossible to cut more than two pieces at one time,
and attempting to do so can damage the unit and
blades.
The bending roller moves even during cutting
operation. Never bring your hand close to the bending
roller.
1. Normal cutting (Fig. 3.)
(1) Turn the lever in the direction of the arrow mark and
open the cover.
(2) Set the setting dial at the cut position. (Turn the
setting dial all the way clockwise.) (Fig. 3.)
(3) Set the unit in the position shown in Fig. 3.
(4) Set the rebar to be cut on the lower cutter.
(Bending)
q Close the cover.
w Select the bending angle.
e Place a rebar.
r Pull the trigger.
(Cutting)
q Open the cover.
w Select CUT.
e Place a rebar.
r Pull the trigger.
(Returning Halfway)
q Select RETURN with the dial.
w Pull the trigger.
Refer to the Handling Instructions for details.
(5) When the rebar is set, make sure that either the
reaction stopper A or B is hitched to the rebar.
(6) Pull the switch trigger and cut the rebar.
CAUTION
For the sake of safe operation, this unit is designed
so that the switch cannot be inadvertently switched
on. When switching the tool on, press the lock button
and then pull the switch trigger (Fig. 2). If the switch
trigger is pulled without pressing the lock button
first, the switch may be damaged. Please use care
when switching the tool on.
Even after the cutting has been completed, continue
pulling the switch trigger until the motor starts to run
in the reverse direction and the cutter starts to return.
If the switch trigger is released too early, the cutter
will not return and the trigger will have to be pulled
again.
2. Removing the rebar during cutting operation. (Fig.
4.)
If the switch trigger is released in the middle of
cutting, the cutter can come to a stop at a halfway
position, jumming the rebar in the unit.
When this occurs, you can either pull the switch
trigger again and cut off the rebar, or you can free the
rebar by bringing the upper cutter back up to the
home position by carrying out the following
procedure. (Fig. 4.)
PICTGRAPH ILLUSTRATION AND
EXPLANATION
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi VB13Y bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi VB13Y in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info