566290
7
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
5
English
TABLE 1
Shift lever indication 1 2
[Low speed gear] [High speed gear]
Dial
Materials to be drilled Types of drills
Drill
ABCDEABCDE
diameters
Brick, Block Diamond φ27
core bit
φ65
φ152
ALC t3.0 Hole saw φ27
φ65
φ120
Steel Hole saw φ15
SPCC t3.0
φ55
Stainless steel Hole saw φ15
t1.6
φ55
Wood Hole saw φ27
t50
φ65
φ120
Steel SPCC t3.0 Drill φ13
Wood t50 Drill φ30
(6) If the core bit starts to vibrate and when the core bit
begins to break through the material, reduce pressure
immediately.
(7) After use, store the core bit carefully in its box and
remember that it is a diamond core bit.
cDrilling method by using Pilot Spigotv
For easy positioning, carry out the following steps
when using a diamond core bit.
(1) Make a pilot hole at the center position of the material
to be drilled with a 13 mm stone drill bit.
(2) Attach a pilot spigot to a diamond core bit.
(3) Align the pilot spigot to the pilot hole and begin the
drilling operation to make a guide groove.
(4) When making the guide groove, temporarily stop the
drilling operation and remove the pilot spigot.
(5) Align the diamond core bit with the guide groove and
start the drilling operation again.
CAUTION
When drilling with a diamond core bit, there will be a
high force of reaction load to your hands. Make sure
to hold the handle of the main body and the side
handle.
Safety-Release Clutch
This tool is equipped with a positive type Safety-
Release Clutch. The clutch will slip when a certain
torque level is required, causing the motor to
disengage from the output shaft. When this happens,
the chuck will stop turning.
CAUTION
Immediately pull away the main body when the
Safety-Release Clutch starts its operation.
Do not continue to operate the tool for more than two
seconds while the clutch is slipping.
Do not let the Safety-Release Clutch activate too
frequently.
5. Drilling with a conventional drill bit
(1) Drilling in wood
Use a woodworking drill bit. However, use an
metalworking drill bit when drilling a hole which is
less than 6.5 mm in diameter. The usable drill bit
diameter is maximum 30 mm.
(2) Drilling in mild steel or plastics
Use a conventional metalworking drill bit. The usable
drill bit diameter is minimum 1.2 mm and maximum
13 mm.
CAUTIONS
Pressure:
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result in a
damaged drill bit, decreased drilling efficiency, and/
or shortened service life of the drill.
Using a large diameter drill bit:
The larger the drill bit diameter, the larger the reactive
force on your arm. Be careful not to lose control of
the drill because of this reactive force. To maintain
firm control, establish a good foot-hold, hold the drill
tightly with both hands, and ensure that the drill is
vertical to the material being drilled.
When drilling completely through the material:
When the drill bit bores completely through the
material, careless handling often results in broken
drill bit or damage to the drill body itself due to the
sudden movement of the drill.
Always be alert and ready to release pushing force
when drilling through the material.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi DC120VA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi DC120VA in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info