741835
5
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
5
EN
a omnipolar switch with minimum between-con-
tacts aperture of the overvoltage category III (4000
V),
sized to the load and conforming to current
legal regulations, is fi tted between the appliance
and the mains in the direct connection to the
mains;
the omnipolar switch used for connection is easy
to reach when the appliance is installed;
the yellow/green earth wire is not interrupted
by the switch;
the power supply, when the appliance is operat-
ing, must not deviate from the rated voltage value
by ±10%;
make sure that after inserting the power supply
cord into the terminal block it does not come into
contact with any of the cooking range’s hot parts.
if the supply cable is damaged then it must be
replaced by the manufacturer or by your tech-
nical support or by a qualified person to avoid
any risk.
Connection to the water mains
(for ovens predisposed to humidifi er solenoid-valve)
The appliance must be fed with softened drinking
water, with pressure in the range from 100 to 200 kPa
(1.0
- 2.0 bar). Water must have hardness from 0.5°F to
3°F (it is suggstible to use a softener as to avoid the
malfunction of the fan, the breakage of the heating
element and to reduce the formation of lime inside
the cooking chamber). Connection to the water
mains should be made through the threaded 3/4”
solenoid-valve on the rear (on the bottom) of the
appliance, tting in between a mechanical lter and
an on/off tap (before you connect the lter, allow
a certain quantity of water to ow out in order to
drain any waste from the pipe).
Connection to water tank
(for ovens predisposed to water pump)
To replace electrovalve with water pump (in ovens
with
optional predisposition to pump), follow the
steps below listed (image 1):
1. Remove back cover from oven.
2. Disconnect wiring cables from electrovalve.
3. Disconnect water tube (3) from electrovalve,
pressing e keeping pressed the edge of black
linking (quick insertion).
4. Remove the electrovalve unscrewing the screw
that fi x it to oven’s frame.
5. Fix the pump (1) to the frame with the appropri-
ate support (2) and the two screws (4) included.
6. Connect the cables previously disconnected from
electrovalve to pump.
7. Connect the tube previously disconnected from
electrovalve to pump’s linking.
8.
Connect the tube (6) with lter and ballast (includ-
ed
in “Pump kit”) to pump’s apron (7).
9. Replace back cover.
Warning:
To avoid limestone buildup into the cooking chamber,
we suggest to ll the water tank with decalcifi ed water.
Check water level in the tank before activating the
pump and during its functioning. If pump works with-
out water in the tank, what occurs is abnormal noise
at first and then its breakage.
Fig. 1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hendi 225059 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hendi 225059 in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 1,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info