665716
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7 / 12
Recommendation to reduce electro-magnetic emission
a. Mains power supply: the equipment must be connected to the power mains as specified in the Manufacturer’s instructions. If interference
occurs, additional precautions such as filtering of the mains supply may be required. The supply cable in the welding machine’s permanent
installations may have to be screened in metal conduits or similar. The screening should be electrically continuous for the entire length of the
cable. It should also be connected to the welding machine with a good electrical contact between the metal conduit and the casing.
b. Welding cables: The welding cables should be kept as short as possible and should be positioned close together, running at or close to the
floor level.
c. Protection and reinforcement: Selective screening and shielding of other cables and equipment in the surrounding area may alleviate
problems of interference. Screening of the entire welding area may be considered for special applications
d. Connect the earth directly to the metal piece to be welded: Where necessary, the connection of the workpiece to earth should be
made by a direct connection to the workpiece, but in some countries where direct connection is not permitted, the connection should be
achieved by suitable capacitance, selected according to national regulations.
T
ROUBLESHOOTING
Anomalies Causes Remedies
Thermal protection light switched on, the
welding unit do not supply current.
The thermal protection of the welding unit is
switched on.
Wait until the end of the cooling phase.
Only the green indicator is on but you cannot
weld.
Connection failure of the earth clamp or
electrode holder.
Check the connections.
If, when the unit is on and you put your hand
on the welding unit’s body, you feel tingling
connection.
The welding unit is not correctly connected to
the earth.
Check the plug and the earth of your electrical
network.
Your unit does not weld correctly. Polarity error (+/-).
Check the polarity advised on the electrode
packaging.
The green indicator is on but the fan does not
work or not continuously, no power when
welding.
Power supply other than 230 or 400V
(EXPERT 220 DV)
Check if the plug delivers the correct voltage.
Switch off the machine for 2-3 minutes and try
again.
D
ECLARATION OF COMPLIANCE
The equipment described on this manual is complies with the instructions of low voltage 2006/95/CE of 12/12/2006, and the instructions of CEM
2004/108/CE of the 15/12/2004. This conformity respects the standards EN60974-1 of 2005, EN 50445 de 2008, EN60974-10 of 2007.
CE marking was added in 2012.
01/06/12
Société GYS
134 BD des Loges
53941 Saint Berthevin
Nicolas BOUYGUES
Président Directeur Général
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys Expert 220 DV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys Expert 220 DV in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 2,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info