779067
5
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
9
56 Flat washer ɸ10xɸ14 1
57 Hex nut M10x6T 3
58 Allen screw M8x36 1
59 Allen screw M6x12 1
60 Spring 1
61 Screw M5x4 4
62 Screw M4x12 5
63 Allen screw with round head
M8x40
2
64 Lock nut M8 2
65 Allen screw with round head
M8x16
2
66 Handlebar plug ɸ 25 2
67 Sensor bracket 1
68 Sensor cable 1
69 Controller 1
3.2. PREPARING FOR USE
3.2.1. APPLIANCE LOCATION
The device should always be used when positioned on an
even, stable, clean, reproof and dry surface, and be out of
the reach of children and persons with limited mental and
sensory functions. It is recommended to properly protect
the oor against possible damage (using special mats).
3.2.2. ASSEMBLING THE DEVICE
I. Attach the front stabilizer (2) to the frame (1) with
two bolts (44), two washers (45), and two nuts (46).
Install the rear stabilizer (3) in the same way.
II. Please note: The bike has levelling feet (10). To level
the bike, turn the feet (10) left or right.
III. Loosen the adjustment knob (24) and insert the seat
post (4) into the frame (1). Adjust the seat post (4) to
the desired height and tighten the adjustment knob
(24). Place the horizontal saddle support (5) on the
seat post (4). Fix the saddle (28) on the support (5),
secure the seat by tightening the knob (25).
IV. Loosen the headset (38) and insert the handlebar
stem (7) in the front of the frame (1). Then, tighten
the adjustable handle (38). Place the lower handlebar
cover (41) on the handlebar stem (7). Use two bolts
(65), two spring washers (50), two at washers (51) to
attach the handlebar (6) to the stem (7). Fasten the
upper and lower handlebar covers (41,43) with four
screws (47).
V. Attach the control unit (69) to the handlebar (6).
Connect the sensor wire (68) running from the
control unit (69) to the frame (1).
VI. Please note: When connecting the wire, the
connecting parts should be on the same side.
VII. Tighten the left pedal (20) counter clockwise and the
right pedal (22) clockwise (the pedals are marked:
„L“ left and „R“ right). Make sure that the pedals
are xed properly, according to the markings. The
crank plug (23) must be rmly xed in the crank bore,
otherwise the threads might become worn.
Please note: You can lubricate the threads before
assembling the pedals.
Please note: The pedals must be tightened very
rmly. After one week of use, tighten them again.
3.3. CONTROLLER
CONTROLLER UNIT DESCRIPTION
1. Button „RESET”
2. Button „MODE”
3. Button „SET”
4. Display
CONTROL UNIT FUNCTIONS
MODE: Switching between functions is possible
using the „MODE“ button, continue pressing the
„MODE“ button until the appropriate function is
selected. Pressing and holding the button for 4
seconds resets the value (not applicable to ODO).
SET: Setting values for: time, distance, calories.
Pressing and holding automatically increases the
value.
RESET: Pressing the button resets the value.
1
2
3
4
8
l) Put the device on a stable, dry and at surface, taking
care to keep a minimum space of 0,6 m space around
the device.
m) It is not recommended to use the device without
prior consultation with a doctor by:
persons with contraindications from the doctor or
feeling ill,
persons with serious illnesses,
people suering from diseases such as hypertension,
heart disease, atherosclerosis and cerebral vein
thrombosis,
people suering from osteoporosis,
people with a pacemaker or other implanted medical
device.
n) Do not use the device one hour before or one hour
after a meal as undesirable eects may occur.
o) Keep the device away from moisture and dust.
p) Only one person at a time can use the device.
q) Stop exercising when you feel tired or exhausted.
r) Do not use the equipment for therapeutic purposes.
Part
number Name Quantity
1Frame 1
2Front stabilizer 1
3Rear stabilizer 1
4 Seat post 1
5Horizontal saddle support 1
6Handlebar 1
7Handlebar stem 1
8Magnetic grip 1
9Mounting angle 1
10 Levelling feet ɸ25xM8 4
11 Plug 4
12 Inner belt cover 1
13 Drive belt 5PJ550 1
14 Bearing 2
15 Compression springs ɸ20 2
16 Wheel 1
17 Wheel axle 1
18 Belt outer cover 1
19 Left crank 9/16‘’165 1
20 Left pedal 9/16” 1
21 Right crank 9/16‘’165 1
22 Right pedal 9/16” 1
23 Crank plug 2
24 Adjustment knob M16x1,15P 1
25 Adjustment knob M8 1
26 Saddle support plug 25x50x1,5T 2
27 Saddle locking bracket 1
28 The saddle 1
29 Front belt cover 1
30 Flywheel axle ɸ12x127xM10x1P 1
31 Flywheel bearing 6001 2
32 Flywheel ɸ420 1
33 Sleeve ɸ16xɸ13x14 1
34 Brake rod cover 1
35 Brake knob 1
36 Brake cover 1
37 Transport wheel 2
38 Adjustable handle M10x1,5P 1
39 Internal insert 50x100x1,5T 1
40 Internal insert 40x80x1,5T 1
41 Lower cover 1
42 Handlebar protective cover 2
43 Top cover 1
44 Screw M8x55 4
45 Pad ɸ7 4
46 Convex nut M8 4
47 Screw ST4.2x16 10
48 Screw ST4.2x16 6
49 Outer screw M8x16 4
50 Spring washer ɸ8 6
51 Flat washer ɸ8 8
52 Clamping nut M10 1
53 Tightening bolt set 1
54 Set of pressure rollers 1
55 Hex nut M10x8T 2
LIST OF PARTS
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The device is designed to simulate cycling. The product is
intended for home use only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. ASSEMBLY DRAWING
ATTENTION! This product‘s view can be found on the
last pages of the operating instructions (pp. 31). ATTENTION! This product’s exploded view can be
found on the last pages of the operating instructions
(pp. 32-37).
Name Function
TIME Total exercise time
SPEED Current speed
DISTANCE Distance covered
CALORIE Calories burned
ODO Total distance (from the start of the
battery operation)
SCAN
Automatically displays the above
functions (TIME-SPEED-DISTANCE-
CALORIE-ODO)
3.4. DEVICE USE
Please note: When the device is not in use, the display will
turn o automatically after approx. 4-5 minutes.
VERTICAL ADJUSTMENT OF THE SADDLE
To adjust the saddle height, loosen the adjustment knob
(24). Adjust the vertical seat post to the desired height with
the holes aligned, then tighten the knob.
30.10.2020
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gymrex GR-MG13 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gymrex GR-MG13 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 5.68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info