623132
28
Verklein
Vergroot
Pagina terug
1/213
Pagina verder
9. Operation
Drilling Speeds
Factors influencing the drilling sped: type of material. drilled hole size. type of bit. required quality of cut.
Remember that the smaller the bit is the larger is the required speed. When drilling soft materials. higher
speed is required than that for the hard materials (see the table of drilling specifications).
Metal Drilling
Metal pieces need to be clamped safely. some of our vices are recommended. Never hold the piece just with
hands. The bit cutting edges may catch the piece and cause a serious injury to you. The bit will get broken
when a metal object strikes against the column. .
The piece to be drilled should be firmly clamped. Any tilting. twisting and shifting will result in a rough drilled
hole and the risk of breaking the bit will increase as well. If the metal object is flat. underlay it with a piece of
wood to prevent spinning. If the shape is irregular and its area cannot lie on the bench entirely. it should be
fixed.
Wood Drilling
It is possible to use the metal working bits for wood working as well. however. wood drilling bits should be
preferred. Do not use twist drills. those rotate so fast that they will lift the drilled piece from the bench and will
spin it around. To drill the material through. the bench has to be aligned for the bit to get in the centre hole.
When the bit starts cutting wood. the advance should add gradually to prevent the material from shattering.
Put a piece of waste wood under the worked material as a pad. It will help to reduce the shattering qualities
and protect the drill bit tip.
Advancement
Apply sufficient force on the advancement hand lever to press it down. interrupt the advancement now and
then to keep the chips short or to direct the sawdust from the hole being drilled. Too fast advancement could
result in the motor stopping. belt slipping. damaging the piece being drilled or breaking the bit. Too slow
advancement could heat the drilling bit and the piece being drilled could get burnt.
10. Maintenance
WARNING: SWITCH OVER TO “OFF” POSITION AND UNPLUG THE MACHINE BEFORE
MAINTENANCE OR LUBRICATION OF THE MACHINE FOR YOU TO BE SAFE.
Blow off or suck off any sawdust and chips gather on the motor. pulley housing. bench and the drilled piece
surface.
Wipe the gloss surface with an oiled cloth.
Apply a layer of pasty wax on the column and the bench to keep the surfaces clean with any spots of rust.
The ball bearings in the pinion and v-belt pulley assembly are lubricated for life and sealed permanently. Pull
the pinion down and lubricate with oil on a three-month basis.
If the bench clamping devices and locking knobs run heavily. lubricate them.
CAUTION: Any routine and scheduled maintenance of the drill should be done by an authorised
servicing technician.
28
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude GTB 20 55194 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude GTB 20 55194 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 3,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info