625851
35
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
Mind to wear safety shoes to operate the plate vibrator – it is the only way of avoiding injuries and contusions
Prior to the commissioning
• manual and sure to follow safety instructions listed.
• Engine oil fill and oil level to ensure correct.
• Fuel (unleaded petrol) fill.
• Safety clothing
Installation and Commissioning (Fig. 1 / 2)
• Attach the handle (1) of the vibratory plates by screws on the guide bar (8).
Launch
• petrol tap (17)
• During cold engine WINDOW Choke, choke the engine in warm open (14)
• motor switch to "ON" (7)
• throttle slightly open (15)
• Starterseil draw - Note: If the oil level is too low the engine will not jump to.
• choke open while the engine warmläuft
• throttle fully open for operation
Parking
• Close throttle and idle speed to bring
• motor switch to "OFF" switch
• petrol cock closed
Step-by Step Instructions
1. Clear any foreign objects from the ground to be treated with the vibrator .
2. Always wear protection clothing .
3. Start the plate vibrator according to description in the manual. .
4. Observe all the relevant safety instructions and protection measures. .
5. Compact the ground to be treated slowly and evenly to obtain the best possible result.
Troubles-Causes-Troubleshooting
Trouble Cause Troubleshooting
Engine cannot be
started
1. Switch ON/OFF position .
2. No fuel
1. Refuel.
Engine runs unevenly
1. Engine gas lever still in the choke position .
2. Ignition plug loosened .
3. Dirty or dead fuel .
4. Jammed air filter .
5. Carburettor misadjusted .
6. Tank cover vent jammed .
1. Put the gas lever in position run.
2. Check the ignition plug .
3. Drain the dead fuel in a suitable container.
Pour fresh fuel in the tank .
4. Clean the air filter .
5. Have the carburettor adjusted .
6. Clean the tank cover and the vent .
Engine runs but the
machine will not be
vibrating
1. Not fully opened gas lever .
2. V-belt loosened or broken .
1. Open the lever at full .
2. Set up/replace V-belt (see inspections and
maintenance)
The plate slats or runs
unevenly
1. Loosened or damaged dampers .
2. Surface too hard .
1. Check the dampers, retighten or replace.
Inspections and Maintenance Safety Instructions
Turn the engine off before repairs, maintenance and leaving the vibrator .
Inspection and maintenance
V-belts
For new machines or installing a new belt, the belt tension after the first five hours of operation be reviewed. Then the belt every 50
hours of check and adjust.
Adjusting the strap
• The four screws on the strap loose and the protection belt protection decrease.
• The four screws that secure the engine to the console is attached, and the mother, with the rear part of the belt protection on the
console is attached, detach.
• The engine on the tightening of the belt to the rear (in the direction of handle), the loosening of the belt to the front slide.
35
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude GRP 2500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude GRP 2500 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info