110462
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
ENGLISH
14
Setting up the device
The speaker for the device is located at the bottom of
the device.
To optimise the sound, mount the device holder on the
bottom of the device.
UP MODE
DOWN TIMER
VOL.
MEMO
SET
ON OFF
1 2
543
6 7
8 9 10
1 Click the device
holder in place in
the recesses on the
bottom of the
device.
Mounting the device under the counter
The fixing screws can be found in the side compart-
ment of the packing.
ONOFF
1 2
543
6 7
8 9 10
UP MODE
DOWN TIMER
VOL.
1 Mark the locations
for four mounting
screws.
2 Screw the device
holder on with four
screws.
UP MODE
DOWN TIMER
VOL.
MEMO
SET
ONOFF
1 2
543
6 7
8 9 10
3 Insert the device in
the holder.
Note:
7
To remove the device, press the snap-catch at
the back and remove by pulling forward.
Setting radio stations
There are 10 channel positions available for radio sta-
tions.
1 Switch on the device with »ON/OFF«.
2 Begin station search by pressing and holding down
»UP« or »DOWN«.
The search stops, as soon as a radio station with a
sufficiently strong signal is found.
If RDS information is transmitted by the station cur-
rently set, »f« appears in the display and after a
short time the station name appears in place of
the frequency.
INSTALLATION AND SETTINGS ________________
Note:
7
You can also set the frequency step-by-step
(50 kHz) by briefly pressing »UP« or »DOWN«.
Only 100 kHz steps are shown in the display.
3 Save radio station by pressing »MEMORY«
P -« flashes in the display ), select the desired chan-
nel position within 8 seconds with »1 10« and
confirm with »MEMO SET«.
»1 … 10« press once for channel positions
1 … 5, twice for channel positions 6 … 10.
Display: the channel position is shown briefly, and
then the frequency.
4 To set further radio stations, repeat this procedure
starting at pt. 2.
Note:
7
If no channel position is selected within 8 sec-
onds, the device interrupts the setting procedure.
Start again at pt. 3.
Setting the time automatically
1 Select a channel position with an RDS station to au-
tomatically set the time.
The display »¥« flashes, the current time is set by
the RDS time signal. This process may last a few min-
utes.
If an RDS time signal was received, the indicator
»¥« is illuminated.
Note:
7
If the time is not automatically set, select another
channel position with an RDS station by pressing
»1 10«, »¥« flashes in the display.
7
If your device cannot automatically set the time,
you can enter the time manually.
Setting the time manually
1 Switch off device with »ON/OFF«.
In the display, »12:00« flashes.
2 Press »MEMO SET« and hold down.
3 Set the time with »UP« or »DOWN«.
When »UP« or »DOWN« are held down, the
time can be set more quickly.
4 Release »MEMO SET«.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Grundig Sonoclock 890 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Grundig Sonoclock 890 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Grundig Sonoclock 890

Grundig Sonoclock 890 Gebruiksaanwijzing - Nederlands - 13 pagina's

Grundig Sonoclock 890 Gebruiksaanwijzing - Deutsch - 11 pagina's

Grundig Sonoclock 890 Gebruiksaanwijzing - Français - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info