569642
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Setting the time zone
The time signal transmitter DCF 77 transmits the time
valid in middle-europe, or the Daylight Saving Time of
middle-europe. When using your Sonoclock 720 e.g.
in the U.K., you can set the clock one hour earlier, as
follows:
Disconnect the mains plug to the wall socket.
Remove the standby battery (if fitted)
Press and hold the TIME button while inserting the
AC mains plug in the socket.
The Sonoclock will start to receive the DCF time
signals and will automatically adjust the time one
hour earlier than the received DCF time.
Automatic time setting
When the clock has been connected to the mains
supply or when a standby battery has been fitted, the
built-in microprocessor will automatically activate the
receiver of the Radio Controlled Clock to search for
the DCF time signals and set itself exactly
corresponding to the time signal.
If the synchronisation is impossible due to possible
sources of interference (e.g. thunderstorms, nearby TV
sets, computers or household appliances which are
not radio-suppressed, etc.), the sonoclock 720 will
continue to try receiving the radio time signal until it
succeeds.
If a DCF time is successfully received during the last
hour, the DCF 6 LED (right of the display) lights up.
The LED goes out again when no correct signal is
received in the last hour.
Once the time has been set automatically, the clock
continues running being controlled by the internal
quartz time base (4,19 MHz).
The precision of the clock is not significantly affected
even in case the synchronisation is only successful a few
times per day.
Manual time setting
(if no time signal is received)
Press the TIME button and hold it pressed.
Use the A and B buttons to set the time.
A single press of the A or B button changes
the setting by 1 minute. If the button is held
pressed, the setting changes continuously.
Release the TIME button.
Indicating the seconds
Press the SNOOZE button and hold it pressed.
The display shows the running seconds.
Radio Reception
Switch on and off with the function selection
switch RADIO/ALARM 0 y ɷ :
Setting y = radio off
Setting 0 = radio on
Select the waveband with the BAND switch:
FM = VHF
MW =
Medium Wave
Tune to stations with the rotary control TUNING.
Adjust the volume with the rotary control
VOLUME.
Aerials
For receiving MW stations there is a ferrite
rod aerial inside the set.
Rotating the unit slightly can improve
reception.
The wire aerial at the back of the set is used
for VHF (FM) reception.
Position the wire aerial so that optimum
reception is obtained.
Showing the DCF signal strength
By pressing at the same time the TIME
and SNOOZE keys, the DCF reception is
started all over again.
The display shows the signal strength
and the seconds.
The signal strength is shown in 7 steps:
‘6’ indicates a very good reception and
‘0’ indicates that no signal is being
received.
This indication is shown on the display
until a DCF time has been received
correctly or until the TIME key is pressed.
CLOCK SYNCHRONISATION CLOCK / RADIO
10
Sonoclock 720 page 10
GB
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Grundig Sonoclock 720 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Grundig Sonoclock 720 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Grundig Sonoclock 720

Grundig Sonoclock 720 Gebruiksaanwijzing - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info