505533
8
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
Tools and materials you need
Screwdriver
Electric drill 1/8 carbide drill bit
Mounting screws
Use 0 AWG power wire (min. 50 mm²)
Use 0 AWG ground wire (min. 50 mm²)
Use 11 AWG speaker cable (min. 4 mm²)
Caution!
Please use great caution drilling your trunk, your gas tank and brake lines can be damaged by
puncturing with your drillbit – this could cause damage or failure of your cars operating systems.
As a precaution it is advisable to disconnect the vehicle’s battery before making connection to the
+12 Volts supply wiring (see owner’s manual of your car for further information!).
0 AWG / min. 50 mm² (thicker if planning for additional amplifiers) wire is recommended both the
power and grounds. Both types are available at most Mobile audio dealers or installation shops.
Please consider the enormous power consumption (up to 900A) of these amps when designing the
setup. We strongly recommend to install one or better more additionally batteries. Too little power
from the battery / alternator may cause defects
WARNING
High powered audio systems in a vehicle are capable of generating „Live Concert“ high level of
sound pressure. Continued exposure to excessively high volume sound levels may cause hearing
loss or damage. Also, operation of a motor vehicle while listening to audio equipment at high
volume levels may impair your ability to hear external sound such as; horns, warning signals, or
emergency vehicles, thus constituting to a potential traffic hazard. For safety reasons we
recommends listening at lower volume levels while driving.
Planning your system
a) select a suitable location that is convenient for mounting, is accessible for wiring and has enough
room for air circulation and cooling.
b) If your radio is equipped with preamplifier outputs (RCA), it is advisable to use them.
Mounting your amplifier
Select a suitable location that is convenient for mounting, is accessible for wiring and has ample
room for air circulation and cooling.
Use the amplifier a template to mark the mounting holes, remote the amplifier and drill 6 holes (use
extreme caution, inspect underneath surface before drilling!)
Secure the amplifier using the screws provided
Connections
Connections
1.) GROUND: To vehicle Chassis
To avoid ignition noise caused by ground loops, it is necessary that the amplifiers be grounded to a clean, bare
metal surface of the vehicles chassis.
NOTE: GROUND WIRE SHOLD NOT BE EXTENDED MORE THAN 3 FT.(1 Meter) min. 0 AWG / 50mm²
2.) +12 Volt (Fused) Constant power: To Battery (+)
Due to the power requirements of the amplifier, this connection should be made directly to the positive (+)
terminal of battery. For safety reasons, install an in-line fuse holder (not included) as close to the battery positive
(+) terminal as possible with a rating not exceeding value of fuses in amp.
3.) Remote Turn-On Input: to power antenna output of car stereo
This amplifier is turned ”ON” remotely when the vehicle’s stereo is turned ”ON”.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ground zero GZPA 1.6K-HC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ground zero GZPA 1.6K-HC in de taal/talen: Duits als bijlage per email.

De handleiding is 1,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info