759440
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
2
GB
Applications
The fitting can be operated with:
pressurised storage heaters,
thermally-controlled instantaneous heaters,
hydraulically-controlled instantaneous heaters.
Operation with unpressurised storage heaters is not
possible.
Technical data
Flow pressure: min. 1 bar/recommended 2 - 5 bar
Operating pressure: max. 10 bar
Test pressure 16 bar
If static pressure exceeds 5 bar, a pressure-reducing valve
must be fitted.
Avoid major pressure differences between hot and cold water
supply.
Flow rate at 3 bar flow pressure: approx. 9 l/min
Temperature
- Hot water supply: max. 70 °C
- Recommended (energy saving): 60°C
Water connection: cold - right
hot - left
Installation
Refer to the dimensional drawing on fold-out page I.
Install sink mixer, see fold-out page II, Figs. [1] and [2].
Insert fitting into sink. This will require leading through the
hoses one at a time.
Flush pipes thoroughly before and after installation
(observe EN 806).
Connect fitting, see Figs. [2] and [3].
1. The cold water supply must be connected on the right and
the hot water supply on the left, see Fig. [3].
2. Connect the pressure hose marked red to the left service
valve (hot water).
3. Fit plug-in connector (A) to the right service valve (cold
water).
4. Connect the two short pressure hoses marked blue (arrows
point towards the fitting) to plug-in connector (A).
5. Connect the long pressure hose marked blue (arrow
pointing towards the filter).
6. Connect the long pressure hose marked blue (arrow
pointing from the filter towards the fitting).
Open hot and cold water supply and check that
connections are watertight.
Operation
Open lever (B) to draw mixed water, see fold-out page II,
Fig. [4].
Rotate handle (C) to draw off filtered water.
Maintenance
Inspect and clean all components and replace if necessary.
I. Cartridge (D), see fold-out page II, Fig. [5].
1. Shut off hot and cold water supply.
2. Lever out plug (E) and loosen set screw (F).
3. Remove lever (B) and cap (G).
4. Loosen screw coupling (H) and remove cartridge (D).
Assemble in reverse order.
When installing cartridge (D), ensure that the seals are
correctly seated. Screw in screw coupling (H) and tighten.
II. Ceramic headpart (I), see Fig. [6].
1. Shut off hot and cold water supply.
2. Close handle (C) and remove.
3. Remove snap insert (J) and stop (K).
4. Replace complete ceramic headpart (I) or O-ring (I1).
Assemble in reverse order.
Observe the correct installation position of stop (K).
III. Mousseur
Remove and clean mousseur (64 374), see fold-out page III.
Assemble in reverse order.
Replacement parts
See fold-out page III (* = special accessories).
Care
For directions on the care of this fitting, please refer to the
accompanying care information.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Grohe 33251 Blue bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Grohe 33251 Blue in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info