708326
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
37. Log supported both ends
38. Bucking a log
39. Stand on uphill side when cutting because log may
roll
ASSEMBLY
This chain saw does not require assembly, but user should
know how to assemble the guide bar and saw chain.
Check the chain tensioning and add oil as described later
in this manual before each operation.
ASSEMBLING THE GUIDE BAR AND SAW CHAIN
See gure 2 - 7
Make sure remove the battery pack from the unit. Wear
protective gloves.
Unscrew the sprocket cover tighten knob (item 10)
and remove the sprocket cover.
The saw chain should face in the direction of chain
rotation. If they face backwards, turn the loop over.
Place the chain drive links into the bar groove.
Position the chain so there is a loop at the back of
the bar.
Hold the chain in position on the bar and place
the loop around the sprocket and make sure it is
correctly mounted. Make sure the bar hole ts well
with bolt (item 16) for saw chain tension.
Replace the sprocket cover, turn the chain tension
adjust knob (item 11) clockwise until the saw chain
is properly tensioned. The guide bar must then be
pushed upwards, check chain tension again, do not
tension the chain too tight.
After the chain is well-tensioned, tighten the knob
(item 10) again.
NOTE: The saw chain is properly tensioned if, in the
middle of the guide bar, it can be lifted 3mm to 4mm from
the edge of the guide bar. Start the saw again with a new
saw chain, allowing it to run-in for 2~3 minutes.
WARNING
After the run-in time, check the chain tension and
retighten the chain if necessary.
OPERATION
For complete charging instructions, refer to the
Operators Manuals for your Greenwork battery pack
and charger models.
NOTE: To avoid serious personal injury, always remove
the battery pack and keep hands clear of the lock-out
button when carrying or transporting the tool.
BEFORE EACH USE CHECKING THE CHAIN
TENSION
WARNING
Remove the battery pack from the chain saw before
checking the chain tension or making adjustments to
the chain. Wear protective gloves while touching the
chain, bar or areas around the chain.
Pull the chain in the middle of the lower side of the bar
away from the bar. The gap between the cutter in the
chain and the bar should be between 3mm - 4mm.
If you need to adjust the chain tension, please refer to
the section “ADJUSTING THE CHAIN TENSION” later
in this manual.
TO INSTALL BATTERY PACK
See Figure 2.
Align the battery pack with the battery compartment
on the chain saw.
Grasp the chain saw firmly.
Push the battery pack into the battery compartment
until the latch locks into place.
You should hear a "click" once the battery is installed.
TO REMOVE BATTERY PACK
See Figure 2.
Press the battery release button on the chain saw.
This will cause the battery to raise out of the tool
slightly.
Grasp the chain saw firmly, and pull the battery pack
out of handle.
CHECKING THE CHAIN LUBRICANT
See Figure 2.
Check the amount of oil in the chain saw by looking
at the quick view oil indicator ( item 5). If the oil level
is low, follow the steps shown in section “ADDING
CHAIN & BAR LUBRICANT” of this manual.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Greenworks GD60CS40 - 2001807 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Greenworks GD60CS40 - 2001807 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info