708325
7
Verklein
Vergroot
Pagina terug
1/305
Pagina verder
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
6
Place the chain drive links into the bar
groove.
Position the chain so there is a loop at
the back of the bar.
Hold the chain in position on the
bar and place the loop around the
sprocket.
Fit the bar ush against the mounting
surface so that the bar studs are in the
long slot of the bar. Ensure that the
chain is over the sprocket. Replace the
chain cover.
Remove all slack from the chain by
turning the chain adjustment screw
clockwise until the chain seats snugly
against the bar with the drive links in
the bar groove.
Lift the tip of the guide bar up to check
for sag.
Release the tip of the guide bar and
turn the chain adjustment screw 1/2
turn clockwise. Repeat this process
until sag does not exist.
Hold the tip of the guide bar up and
tighten the chain cover lock nuts by
turning them with the wrench. The
chain is correctly tensioned when
there is no sag on the underside of the
guide bar, the chain is snug, but it can
be turned by hand without binding.
ADDING CHAIN & BAR LUBRICANT
Unscrew and remove the cap from the
oil tank.
Pour the oil into the oil tank and monitor
the oil level gauge. Ensure that no dirt
enters the oil tank while lling the oil in.
Put the oil cap back on and tighten it
up.
One full oil tank will enable you to use
the saw for 20- 40 min.
TRANSPORTING THE TOP HANDLE SAW
Before transporting the top handle saw, al-
ways remove the battery pack from the top
handle saw and slide the chain cover over
the bar and chain. If several cuts are to be
performed with the top handle saw, the saw
must be switch off between cuts.
GUIDE BAR COVER
See gure 1
The chain cover must be clipped onto the
chain and bar as soon as the sawing work has
been completed and whenever the machine
has to be transported.
SHARPENING THE SAW CHAIN
See gure 16 - 21
When the chain penetrates into wood with
difculty, it needs sharpening as follows:
Put the chain under tension.
Fasten the bar in a vice so that the
chain can slide.
Fasten the le to the le holder and
place it on cutter at 35° angle.
File with forward strokes only until all
the worn out parts of the cutting edge
are taken away.
Count the number of strokes given to the
cutter as a reference and le away with
the same number of strokes on all other
cutters.
If the depth gauge protrudes from the
template after sharpening a few times,
reset its level. Use a at le. Finally,
round off the depth gauge.
NOTE: It is recommended to have the deep
or important sharpening carried out by a
service agent who is equipped with electric
sharpener.
GUIDE BAR MAINTENANCE
When you have nished working, clean
out the groove and the oil passages
with a scraping hook.
Periodically trim the sides of rails using
a at le. If not done in the long run,
the feather edges might break away
and damage the bar.
If one rail is higher than the other one,
it is necessary to make it even with a
at le then smooth it with a le or ne
grain abrasive paper.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Greenworks GD40TCS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Greenworks GD40TCS in de taal/talen: Alle talen als bijlage per email.

De handleiding is 10,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info