708325
3
Verklein
Vergroot
Pagina terug
1/305
Pagina verder
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
2
11. Wrench
12. Top handle
13. Sprocket cover tighten nuts
14. Sprocket cover
15. Chain tensioner adjustment screw
16. Bolt for saw chain tension
17. Sprocket
18. Battery release button
19. Oil outlet
20. Bar groove
21. Chain drive links
22. Cutter
23. Felling direction
24. Danger zone
25. Escape route
26. Direction of fall
27. Notch
28. Felling back cut
29. Hinge
30. Limb cut
31. Keep work off ground leave support
limbs until log is cut
32. Log supported along the entire length
33. Cut from top (over buck) avoid cutting
earth
34. Log supported one end
35. Under buck
36. Over buck
37. Log supported both ends
38. Bucking a log
39. Stand on uphill side when cutting be-
cause log may roll
ASSEMBLY
This top handle saw requires no assembly,
but user should know how to assemble the
guide bar and saw chain. Check the chain
tensioning and add oil as described later in
this manual before each operation.
ASSEMBLING THE GUIDE BAR AND
SAW CHAIN See figure 2 - 7
Make sure remove the battery pack from
the unit. Wear protective gloves.
Unscrew the sprocket cover tighten
nuts and remove the sprocket cover.
The saw chain should face in the
direction of chain rotation. If they face
backwards, turn the loop over.
Place the chain drive links into the bar
groove.
Position the chain so there is a loop at
the back of the bar.
Hold the chain in position on the bar
and place the loop around the sprocket
and make sure it is correctly mounted.
Make sure the bar hole ts well with
bolt for saw chain tension.
Replace the sprocket cover, turn the
chain tension adjust bolt clockwise until
the saw chain is properly tensioned.
The guide bar must then be pushed
upwards, check chain tension again,
do not tension the chain too tight.
After the chain is well-tensioned,
tighten the nuts again.
NOTE: The saw chain is properly ten-
sioned if, in the middle of the guide bar, it
can be lifted 3mm to 4mm from the edge
of the guide bar. Start the saw again with
a new saw chain, allowing it to run-in for
2~3 minutes.
WARNING
After the run-in time, check the chain ten-
sion and retighten the chain if necessary.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Greenworks GD40TCS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Greenworks GD40TCS in de taal/talen: Alle talen als bijlage per email.

De handleiding is 10,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info