708336
5
Verklein
Vergroot
Pagina terug
1/162
Pagina verder
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SV HR HU RO BG EL AR TR HE LT LV ET
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake uids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorised Service Centre.
SPOOL REPLACEMENT See Figure 12.
Use original manufacturer’s replacement cutting line for
best performance.
Remove the battery pack.
Push in tabs (C) on side of spool cover (A).
Pull spool cover up to remove.
Remove the old spool.
To install the new spool (B), make sure the cutting line
is captured in the slot on the new spool (F). Make sure
the end of the cutting line is extended approximately
15cm beyond the slot.
Install the new spool so that the cutting line and slot
align with the eyelet (E) in the cutting head (G). Thread
the cutting line into the eyelet.
Pull the cutting line extending from the cutting head so
the cutting line releases from the slot in the spool.
Reinstall the spool cover by depressing tabs into slots
(D) and pushing down until spool cover clicks into
place.
CUTTING LINE REPLACEMENT See Figure 13.
Remove the battery pack.
Remove the spool from the cutting head.
NOTE: Remove any old cutting line remaining on the
spool.
Cut a piece of cutting line approximately 3m long.
Insert the cutting line into the anchor hole (B) in the
upper part of the spool. Wind the cutting line around
the upper part of the spool clockwise, as shown by the
arrows on the spool. Place cutting line in the slot (C)
on upper spool flange, leaving about 15 cm. extended
beyond the slot. Do not overfill. After winding the cutting
line, there should be at least 0.635 cm between the
wound cutting line and the outside edge of the spool.
Replace the spool (A), and the spool cover. Refer to
spool replacement earlier in this manual.
4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Greenworks G24LT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Greenworks G24LT in de taal/talen: Alle talen als bijlage per email.

De handleiding is 15,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info