30121
7
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
Mode of Operation Analogue Adjustment
of Values
7
later on. For other applications seven freely
programmable mixers are available.
Type 7: F3B (4 wing servos)
Type 7 corresponds to type 6, with the exc eption
that in the case of type 7 the flaps are actuated
by a separate servo each, thus providing
additional mix options (ailerons-flaps) which are
also realised by a special mixer. Here, too,
seven freely programmable mixers are available.
The universal Profi program can also be used for
models have two wing mounted servos. In this
case the functions not required are left
unoccupied in the receiver.
Type 8: HELI
Type 8 is a universal helicopter program for
practically all helicopters, unless they are not t o
be operated exclusively with an RPM regulator
which can not be turned off or overridden by the
throttle channel. Here one finds all currently
imaginable options for helicopters of all types
and sizes, both for normal operation and for
demanding competition work.
Type 9: HELI (with speed control)
Type 9 is suitable for model helicopters which
are exclusively operated with a speed control
operated via an auxiliary channel. In this case
the compensating functions acting on engine
control are missing. Other control functions
effect the auxiliary channel, which in turn
correspondingly controls the regulator. If a speed
control is used, which can be turned off or
overridden by normal throttle control, type 8
should be used.
The mode of operation permits skimmi ng
through the program of a model by pressing key
LIST-DM , then pressing INC to go forwards
and DEC to go backwards. Aster the desired
code number has been found, the program in
question can be selected using the ENTER key.
The value can then be set using the INC and
DEC keys as well as CLEAR and 1 9 ,
respectively.
The survey of contents is vacated by pressing
the CLEAR key while a new code number and
title of the code appears in the lower line of the
display.
The functions of the INC and DEC keys can
be taken over by a proportional rotary module
(order number 4111) wire to plug station AUX or
a proportional module (order number 4152).
Calling the function is performed as before, but
at that station where adjustments are to be
made, normally by the INC and DEC keys, the
rotary control is activated by key 9 . Adjustments
are then made performed using the rotary
control. In the case where the adjustment range
of the rotary control should prove inadequate to
obtain the desired value, the rotary control has to
be turned off on reaching the end position, via
the DEC key, and then reset to suit, turned on
again via key 9 . This step can be repeated as
often as required.
This analogue adjustment option can, in
principal, be used at all stations where inputs are
possible via INC and DEC keys, including for
example for skimming the list of codes.
If, on imputing the name of the model, the
selection of letter is performed using analogue
setting, numbers, lowercase letters and specia l
symbols will be available in addition to the
normally available capital letters.
After the PROFITRIM-module has been
installed, the right upper control will take over the
functions described above. Its normal function
will be interrupted automatically at the same
time.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graupner MC18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graupner MC18 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Graupner MC18

Graupner MC18 Gebruiksaanwijzing - Deutsch - 188 pagina's

Graupner MC18 Gebruiksaanwijzing - Français - 58 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info