637237
5
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
6
- Mount the bound receiver in the target place in the model.
- Switch on the RC system so that you could observe the movement of the servos.
- Put the model on a at surface (pavement, closely mown grass or earth), and ensure
that the receiver antenna should be at least 15cm above from the ground.
- Face the model with the transmitter in your normal ying position, the antenna on
the transmitter shouldn’t be toward the model directly and it keeps stand horizontally
during range checking
- Enter range check mode of your specic transmitter and follow the procedures of your
specic transmitter to check the range. the transmitter repeat a single beep with a
regular rhythm, indicating the Range checking is processed normally.
- Walk over 50 meters away from the model with controlling the transmitter sticks
constantly and check whether the model is operating normally. You should have total
control of the model with the trainer switch pulled
- If control issues exist within 50 meters, the system should not be used. And contact
your local Service Department of SJ INCORPERATED.
- Range-check is automatically terminated in 90 seconds and it is also terminated by
turning off the range check function of your specic transmitter. the status LED on the
receiver turns solid green when terminated.
- Have your helper position the model and check effective radio range before every
ight while simulate all the servo movements which will take place when the model is
in ght. The ground range must always be at least 50m in order to ensure safe and
reliable model control.
The last bound receiver is the master receiver when the system would be in use. Every
telemetry sensors installed in the model must be connected to the master receiver,
since the only master receiver transmits sensor data through the downlink channel. The
second and all further receivers are operated as the slave mode which are connected
in parallel to the master, with the downlink channel switched off. The control signals can
be passed to a number of receivers simultaneously and also the different signal can be
assigned to each receiver through the Channel Mapping function of the transmitter or
the optional SMART BOX. The typical example would be the use of two servos for each
aileron, etc.
NOTICE : Make sure to double check that transmitter is bound to receiver by turning
off/on transmitter’s power after binging process is completed
2) Range checking
Before every ying session and especially with a new model, it is important to perform a
range check. All Graupner aircraft transmitters incorporate a range testing system which,
when activated, reduces the output power, allowing a range check. Notice that every
ying must not be permitted in the range checking mode and the model is restrained on
the ground. After binding the receiver to the transmitter, switch the on transmitter and
the receiver and wait until the status LED on the receiver turns solid red.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graupner 33505 - GR-12S HoTT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graupner 33505 - GR-12S HoTT in de taal/talen: Engels als bijlage per email.

De handleiding is 1,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Graupner 33505 - GR-12S HoTT

Graupner 33505 - GR-12S HoTT Gebruiksaanwijzing - Deutsch - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info