776255
10
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
10 GMC-I Messtechnik GmbH
7Self-Test
Because it is so easy to perform, the self-test should
be conducted before each use of the AT3-III E.
Please be careful to ensure that the case of the
AT3-III E is not being contacted with devices
under PE or earth potential during the self-test.
Performing the Protective Conductor Test
Ð
Insert the mains plug from the
SECUTEST.../
SECULIFE ST
into the earthing contact outlet (12)
at the AT3-III E.
ÐThe earthing contact plug (13) and the SE-
CUTEST port (14) of the AT3-III E may not be
plugged into the SECUTEST.../SECULIFE ST.
ÐConnect the AT3-III E to mains power.
ÐSet the SECUTEST.../SECULIFE ST to the
protective conductor test individual measure-
ment (RSL/RPE).
ÐContact protective conductor potential at the
mains system which is supplying power to the
AT3-III E with the test probe at the end of the
probe cable from the SECUTEST.../
SECULIFE ST, e.g. at the earthing contact of
an earthing contact outlet. If an excessively
high value or interruption is indicated, the pro-
tective conductor is interrupted.
The AT3-III E test adapter must be disconnected
from the mains, and the error in the electrical
system or the test adapter must be corrected. The
AT3-III E is equipped with a “Trigger IΔn” test key in
order to allow for testing the included IΔn safety
shutdown function at any time.
Performing the IΔn Self-Test
ÐRemove the device under test
(device or extension cable).
ÐSet the SECUTEST.../SECULIFE ST to individ-
ual measurement.
ÐSECUTEST.../SECULIFE ST (as of version
3.1): Select the “DI current” sub-menu (resid-
ual current).
ÐSignal lamps L1, L2 and L3 indicate the pres-
ence of line voltage.
ÐActivate the “Trigger IΔn” key (11).
ÐThe AT3-III E disconnects mains power from
the outlets (1 – 4).
ÐSignal lamps L1, L2 and L3 go out.
ÐThe function LED (10) blinks.
Disconnect the AT3-III E from the mains to re-
set. Reconnect the AT3-III E to the mains.
The test adapter is once again ready for use
after a brief self-test.
Note!
If mains power is not switched during this
test, the fuses in the AT3-III E may have
blown. If the AT3-III E still does not function
correctly after replacing the fuses, it must be
removed from service and repaired.
Measurement is no longer possible!
8 Technical Data
Residual Current Measuring Function
Measuring Range 0 20 mA
Transformation Ratio 1 V per 10 mA
Intrinsic Uncertainty ±(5%
of rdg.
+ 0.05 mA)
Nominal Ranges of Use
Line Voltage
L1/L2/L3/N 207 253 V AC
Frequency 49 51 Hz
Temperature 0 °C +40 °C
Line Voltage
Waveshape sinusoidal
Reference Conditions
Ambient Temperature +23 °C ±2K
Relative Humidity 50% ±5%
Line Voltage 230 V/400 V ±10%
Frequency
of Measured Quantity 50 Hz ±0.2%
Ambient Conditions
Operating Temperatures 10 + 40 °C
Storage Temperatures 25 + 60 °C
Humidity max. 75%, no
condensation allowed
Elevation up to 2000 m
Power Supply
Nominal Line Voltage
3~230/400 V/50 Hz/CAT II
Connection only permissible with overload
protection device In = 16 A I2 1.45 In
Electrical Safety
Standard
DIN VDE 0404-1/-2:2002-5
IEC/EN 61010-1:2010
Contamination degree 2
Safety Class I
Residual Current
Shutdown (4-pole) at approx. 18 mA
Device Fuses F0315 L250V
5 x 20 T32mA L 250 V
DIN EN 60127-2
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gossen Metrawatt AT3-III E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gossen Metrawatt AT3-III E in de taal/talen: Engels als bijlage per email.

De handleiding is 0.59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info