467815
16
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
2928
P operation mode.
I
IP mode allows to use this module in combination with "Stadio Plus"
panels, or to operate as stand alone module. The operation
mode selection is shown on page 27.
To enter into programming mode, a PIN code will be required.
This code of three digits length (override digit zero from left)
is sticked on the relay, placed on the left side of the display.
While programming, the led on the front part of the module
will light red. To exit from the programming mode, wait 20 sec.
from the last operation.
Press C button during 2 seconds.
The left digit display will show number 0.
To validate the code, press C button during 2 seconds:
the display will show the complete code.
In case of valid code, the display will show the
selected operation mode (IP). In case of wrong code,
the display will show the message "E–5" during
10 seconds and will automatically exit from the
programming mode.
Press arrow "DOWN" button to move to the next digit.
The left display will turn off and the center display
will show number 0.
Press arrow "DOWN" button to move to the next digit.
The center display will turn off and the right display
will show number 0.
Press arrow "UP" button till the first PIN digit will appears
on the display.
Press arrow "UP" button till the second PIN digit will
appears on the display.
Press arrow "UP" button till the last PIN digit will appears
on the display.
C
C
alidation of PROXCARD ISO cards
or NEOKEY key holders.
V
IMPORTANT: this module is to be used with ISO cards or key holders
supplied by Golmar. Other proximity items will be not accepted
even if they have the same appearance.
IMPORTANT:
IMPORTANT:
Once a valid PIN code has been introduced, the
display will show the 1st memory position.
Use "UP" and "DOWN" arrows to select the
desired position, from 1 to 500.
Several cards or key holders can be recorded in one
memory position. Remember that the maximum
number of cards or key holders (users) is 500.
When the display shows the desired memory position,
approach the card or key holder to be recorded.
The display will shows the number of cards
recorded in this position (including the one you are
recording). This number will be shown with a dot
on its right bottom part. The display will show the
selected memory position again.
If you are trying to record an already existing card,
the display will show the memory position where
recorded, coming back to the position you are
trying to record it.
Repeat the above steps to record the rest of cards.
To erase existing cards from a specified memory position,
use "UP" and "DOWN" arrows till the display shows
the desired position. Press C button during 3 seconds:
the display will show the number of cards recorded
in this position and will confirm the progress by
showing the message – – –.
To erase all the existing cards, press C button during
15 seconds aproximately: the display will show the
message "IP" once the memory is empty.
C
The module will exit from the programming mode afte 20 seconds of no operation.
The display and the led on the front part of the module will be turned off.
MODULE PROGRAMMING
MODULE PROGRAMMING
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Golmar T4502ML bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Golmar T4502ML in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info