656049
4
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down for one
minute after 10 minutes' working.
Power Output Control
Test Button
Sync Triggering
Slave Trigger Model
Buzz Function
Memory Function
Flash output controller (5) decides different power output, satisfying light requirements
in different environment. The power is adjustable from 5.0 to 8.0 which will be
accordingly shown on the digital display (10). "OF" on the display indicates that the
flash triggering function is shut down. It can automatically discharge power when the
flash output is adjusted from high to low.
To fire the flash without taking a picture, press the test button (9). It can also help
adjust the flash brightness when using together with the flash output controller (5).
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and the
flash will be fired synchronously with
the camera shutter.
Three slave triggering models are
available and can be set by pressing
Slave Model Button (8).
No optical control: The slave triggering indicator (13) is off, indicating the slave
triggering function is shut down.
One fire model: The slave triggering indicator (13) glows blue, indicating the flash
will fire synchronously on one external flash. In this model, the flash can function as an
auxiliary lamp, offering various effects of light and shadow.
Anti-preflash model: The slave triggering indicator (13) glows red, indicating the
flash will receive two external flashes within 2 seconds and will fire synchronously on
the second flash. In this model, the flash can function as an auxiliary lamp, applicable
to TTL system. With this anti-preflash function, synchronization is supported with
cameras having a one-preflash firing system
The sound button (7) is used to decide whether there is sound reminder for ready flash
after recharging. When the buzz indicator (12) is on, the buzz function is working; if it is
off, the buzz function is shut down. A “BI” sound will be heard when it’s fully charged.
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash next
time, the panel setting will be the same as that before powering it off.
Wireless Control Function
Tube Replacement
By using the wireless power-control flash trigger, you can wirelessly control the on-
and-off of your flash, modeling lamp and buzzer, as well as adjust the flash output
level. To start this function, insert the trigger receiver into the Wireless Control Port
(20) and make settings on the trigger. You can also press the camera shutter-release
button to trigger the flash by setting the transmitter hotshoe onto the camera hotshoe.
Shut down the power and remove the power cord before replacing the flash tube and
wear insulated gloves. Then, loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the feet
casing from the old tube and put them on the new tube. Hold two feet of the new tube
and target directly towards the two copper outlets, then push them slightly in. Twine
the iron wire on the stainless steel sheet to fix the flash tube.
- 05 - - 06 -
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Godox Quicker D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Godox Quicker D in de taal/talen: Engels als bijlage per email.

De handleiding is 2,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info