479883
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
3.0 - NEW PIN-CODE PROGRAMMING
The procedure to program pin-code is specified here below as previously described, it is better to
personalize as customer has required.
In this example reported below, supposing that the pin-code is 5-4-6-7.
PAGE 06 - USER MANUAL
To carry out the operation successfully, make sure the required electrical connections
(door push-button and positive under key) are complete.
During PIN-CODE programming phase, if flashes are more than 9, this phase will be
invalid and the system will close the procedure.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
With the system being disarmed, open the driver side door and keep it open.
Turn the vehicle ignition ket to “ON” position.
The status LED will be turned on for one second; during this period, push simultaneously the two
buttons of the remote contol with embossed the padlocks.
A,
and the LED will lighted on.
Push simultaneously the two buttons of the remote contol with embossed the padlocks; the LED will
be turned off.
Turn the vehicle ignition ket to “OFF” position.
After a four second pause, state LED will start with the first sequence of 9 flashes.
At the fifth LED flashing (corresponding at nr.5, first digit of the PIN-CODE), push and release the
button on the status LED.
After a four second pause, state LED will start with a new sequence of 9 flashes.
Athe fourth LED flashing (corresponding at nr.4, second digit of the pin-code) push and release the
button on the status LED.
After a four second pause, state LED will start with a new sequence of 9 flashes.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
After a four second pause, state LED will start with the last sequence of 9 flashes.
At the seventh LED flashing (corresponding at nr.7, fourth digit of the pin-code) push and release
the button on the status LED.
The system will indicate the end of the procedure by two acousic signal with low tone and one with
high tone.
fter this procedure, two acoustic signals will be sent out one with acute tone and the other with
loud tone
4.0 - EMERGENCY DISARMING BY PIN-CODE
The procedure for emergency disarming by pin-code is following, reported below.
Kindly note that the standard pin-code programmed is of the four digit 1-1-1-1.
The same number used for pin-code programmation (5-4-6-7) has been used also for emergency
disarming example.
During PIN-CODE disarming phase, if flashes are more than 9, the procedure will be
.interpret as a theft attempt
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Cause an alarm condition.
Leave the system triggering for the standard alarm timing (about 30 seconds) and wait for the
“inhibit time between two alarm signalling” (LED switched off for 5”).
During this period push and release the push-button of the status LED.
the “emergency procedure disarming”.
After about 4 seconds the first 9 flashing sequence starts.
At the fifth LED flashing (corresponding at nr.5, first digit of the pin-code), push and release the
button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the fourth LED flashing (corresponding at nr.4, second digit of the pin-code), push and release
the button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the seventh LED flashing (corresponding at nr.7, fourth and last digit of the pin-code) push and
release the button on the status LED.
If the code is right, the end of the emergency disarming by pin-code will be indicated by the alarm
with visual/acoustic signalling.
Vice versa, if the inserted numbers are wrong, the alarm will start triggering again; in this case,
repeat all procedure.
From now and on the system is in
This function is used ONLY if “system self-rearming” or “passive arming” functions
have been programmed.
This function is used when the alarm disarming is required, e.g. for maintenance, without any
intervention to the previous programming
o restore normal operating of programmed functions, arm the alarm via the control
T
.
For procedure activation follow the indications reported below:
Arm the system and wait for the end of arming neutral time.
Put the electronic key into the specific receptacle.
Three acoustic signals of the siren and three optical signals of turn signals will indicate the system's
disarming and the above mentioned function deactivation.
remote
!
!
!
!
.
USER MANUAL - PAGE 07
5.0 - GARAGE FUNCTION
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 862 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 862 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Gemini 862

Gemini 862 Gebruiksaanwijzing - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info