479838
5
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
ACCESSORY FUNCTIONS
MEMORY OF LAST ALARM TRIGGERED:
Indications regarding the last alarm condition detected (ALARM MEMORY) are provided by the
status LED as visual signals which differ as a function of the cause that has triggered the alarm. If
any alarms have occurred, this signal emitted when the vehicle engine is started (positive pole under
key in the ON position), after the alarm system has been turned off.
The visual signal is repeated five times and there is a 2” pause between the emission cycles. The
visual signal can be cut off by turning the ignition key to the OFF position.
LED SIGNALS REFLECTING ORIGIN OF ALARM
CONDITION
CAUSE OF ALARM
ß ˜ ß
Power drain sensor
ß ß ˜ ß ß
Positive pole under key
ß ß ß ˜ ß ß ß
Door pushbuttons
ß ß ß ß ˜ ß ß ß ß
Wires cut
ß ß ß ß ß ˜ ß ß ß ß ß
Pushbuttons for bonnet, boot and external sensors
ß ß ß ß ß ß ˜ ß ß ß ß ß ß
External radio sensor
l LED OFF (2 seconds) Y LED ON ( 400mS)
Besides the accessory functions previously described (see “CUTTING OUT THE EXTERNAL SENSORS/
STOPPING WINDOW UPWARD TRAVEL / COMFORT”; “CUTTING OUT THE SIREN” and “MEMORY
OF LAST ALARM TRIGGERED”) the following accessory functions are available and can be programmed
and used by the user or installer:
a) PANIC ALARM
b) ACTIVATION OF ANTI-DISTRACTION / AUTOMATIC DOOR-LOCKING FUNCTIONS
c) DOUBLE PULSE FOR CENTRALIZED UNLOCKING OF DOORS
d) PASSIVE ACTIVATION OF ENGINE IMMOBILIZER FUNCTION
e) GARAGE FUNCTION
PANIC ALARM / CAR FINDER
If enabled, the PANIC ALARM function allows the user to activate the visual and audio alarm signals
deliberately by pressing key 2 on the remote.
This function works regardless of whether the alarm system is ON or OFF. The alarm signal lasts up
to approx. 30”. However, you can silence it at any time by pressing key 2 on the remote again.
Between one PANIC ALARM cycle and the next there is a neutral time of approximately 5” during
which it is not possible to activate the alarm signal again.
While the alarm signal is emitted and during the consequent neutral time, the LED stays on.
IF DURING THE PROGRAMMING PHASE, THE PANIC FUNCTION HAS BEEN DISABLED, THE CAR FINDER
FUNCTION WILL BE ACTIVATED.
The CAR FINDER function allows, with the ALARM ACTIVATED, you to obtain a short visual/audio
signal by pressing key 2 on the remote. This function can be useful to look for the car in a parking lot
or multi-storey garage without creating useless sound pollution.
The brief visual/audio signal consists of a low beep and the simultaneous flashing of the turn
indicators (total length of indication is one second).
NOTE: the emission of the audio signals is subordinate to their being enabled when programming
the accessory functions.
ACTIVATING THE ANTI-DISTRACTION / AUTOMATIC DOOR-LOCKING FUNCTION.
When this function is enabled, it causes the automatic activation of the alarm system if the latter has
been turned off and no voluntary actions are performed by the user (e.g. OPENING A DOOR OR
STARTING THE CAR) within approx. 35”.
The function prevents the vehicle from being left unprotected in cases where, after the activation of
the protection system, key 1 on the remote is pressed accidentally and the alarm system is turned
off by mistake.
The automatic activation of the alarm is evidenced by the regular visual signals described above.
The anti-distraction function activates the centralized door-locking control. Therefore, in
order to prevent involuntary activations of the alarm system, it is INDISPENSABLE to connect
the driver’s side door pushbutton to the alarm system input.
In conjunction with the ACTIVATION OF THE ANTI-DISTRACTION function, the AUTOMATIC
DOOR-LOCKING function is also enabled.
This function allows the automatic management of the centralized locks according to the running
status of the vehicle.
The doors will lock automatically 20” after the engine is started (positive pole under key in the ON
position).
The doors will unlock automatically 1” after the engine is turned off (positive pole under key in the
OFF position).
Locking and unlocking times are programmed during the installation of the alarm system. To prevent
this function from being activated accidentally, the system continuously monitors the status of the
ignition key and the input line of the DOOR AND BOOT PUSHBUTTONS and therefore does not
allow operation of the locks if the DOORS and BOOT are opened manually while starting the engine
or during the 20” after starting it.
DOUBLE PULSE FOR CENTRALIZED DOOR-UNLOCKING FUNCTION
By enabling this function you will obtain, upon the deactivation of the alarm system, a double control
pulse on the door-unlocking line, each pulse lasting 0.5”. This allows the release of the centralized
door locks on cars having the Dead-Lock function, which requires this type of signal.
The function, which can be enabled by programming during installation, is active only if the
opening/closing time of 0.5” is selected.
Selecting an opening/closing time of 6” automatically excludes the double pulse upon opening.
PASSIVE ACTIVATION OF ENGINE IMMOBILIZERS
If enabled, this function automatically activates the double ENGINE IMMOBILIZER function approx.
45” after the engine is turned off. (Automatic activation of the alarm is indicated by the usual
audio/visual signals already described in this document).
Activation of the PASSIVE ALARM ACTIVATION procedure is signaled, when the vehicle engine is
turned off, by the flashing of the turn indicators for approximately one second, overlapped by two
flashes of the LED and the simultaneous emission of two high beeps.
During the time between the activation of the PASSIVE ALARM ACTIVATION and the actual
activation of the protection system, it is possible to temporarily interrupt the activation procedure by
opening the DRIVER’S SIDE DOOR. This allows the user to operate calmly in the vehicle without
activating the alarm system.
This pause mode is indicated by the LED emitting continuous light, and turning off when the vehicle
door is closed, thus indicating the continuation of the activation count.
NOTE: audio signals will be emitted only if they have been enabled when programming the
accessory functions.
GARAGE FUNCTION.
This function lets you suspend the ANTI-DISTRACTION AND PASSIVE ACTIVATION function. It
can be useful for the purpose of facilitating maintenance and/or car washing operations without
having to give the remotes or the electronic keys of the alarm system to the car mechanics.
To activate the GARAGE function, it is indispensable to enable the ANTI-DISTRACTION AND
PASSIVE ACTIVATION functions.
Follow this procedure:
1) With the alarm system deactivated, turn the ignition key to the ON position. The status LED will
turn on for approximately 0.5”.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 7501 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 7501 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info