479853
4
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
WORKING DESCRIPTION
A
LARM ARMING
Press on the transmitter 1 button. The arming is signalled by 1 direction indicator lights flashing and one
acoustic signal (can be excluded).
A
LARM DISARMING
Press on the transmitter 1 button. The disarming is signalled by 3 direction indicator lights flashing and 3
acoustic signalling
(can be excluded); 5
direction indicator lights flashing and 5 audible tones
(can be excluded)
if an alarm condition has occurred.
SPECIAL FUNCTIONS
Panic
Is obtained pressing the transmitter 2 button with the alarm armed or disarmed after the neutral time of 45
seconds. The siren activates for 29 seconds. To de-activate the siren within the 29 seconds, press again on the
transmitter 2 button.
S
IREN EXCLUSION
While alarm disarmed, turn the ignition key of the vehicle to ON. Press on the transmitter 2 button for at least 3
seconds, the LED lights fix till the releasing of the transmitter’s button to signal the siren sound exclusion.
Turn again the ignition key to OFF and arm the alarm system. The disarming of the system sets to zero the
function.
P
ASSIVE ARMING OF THE ENGINE IMMOBILISATION
.
Set the dip-switch N.5 to ON. The passive arming of the engine immobilisation is obtained 5 seconds
after the instrument panel switching off if the system is not armed with the transmitter. 50 seconds before
the delay time of 5 seconds stops the LED lights fix. One-direction indicator lights flashing and one
audible tone (can be excluded) signal the passive arming activation.
The LED flashes to signal the passive arming activation of the engine immobilisation. The passive
arming of the engine immobilisation is obtained turning the ignition key to ON (
the LED lights fix)
and
pressing on one of the transmitter’s button.
The de-activation of the engine immobilisation passive arming is signalled through the LED switching off.
Turn the ignition key to OFF and then start the vehicle.
S
ELF
-
LEARNING OF THE CODE OF A NEW TRANSMITTER
.
1
. Disarm the alarm with the transmitter.
2
. Set the dip-switch N.6 to ON.
3
. Turn the vehicle ignition key to ON for at least 1 second and then to OFF. The LED lights fix till the ignition
key is turned to OFF.
4
. Turn the key to OFF and within 30 seconds press one of the transmitter’s buttons to learn. The LED lights
for 0,5 seconds to signal the code memorisation.
NOTE: If the operation is not carried out within 30 seconds it will be necessary to repeat the operation from
point 3.
It is possible to learn a maximum number of 4 transmitters; for each transmitter’s coding repeat the operation from point 3.
ATTENTION! A
T THE END OF THE PROCEDURE SET THE DIP
-
SWITCH
N.6
TO
OFF.
U
LTRASONIC SENSOR EXCLUSION AND WINDOWS CLOSURE
.
During the first 25 seconds of neutral time, it is possible to de-activate the ultrasonic sensors and to stop the
window closure pressing on the transmitter 2 button. One-direction indicator lights flashing signals the
operation.
If the time set is 1,5 or 6 seconds, the exclusion of the ultrasonic inlet disables the positive outlet on the alarm
Pink wire (+A); to obtain the disabling of the closure relay set the comfort time of 25 seconds.
To exclude the ultrasonic inlet with the windows completely closed; it is necessary to wait the complete closure
of the window and to press on the transmitter 2 button.
A
COUSTIC SIGNALLING EXCLUSION
(C
HIRP
)
1
. While alarm disarmed, turn the ignition key of the vehicle to ON.
2
. Press on the transmitter 1 button for at least 3 seconds. The LED flashes for 0,5 seconds to signal the
audible tone exclusion.
3
. Position again the vehicle ignition key to OFF.
CHIRP
FUNCTION ACTIVATION
.
1
. While alarm disarmed turn the vehicle ignition key to ON.
2
. Press on the transmitter 1 button for at least 3 seconds. The LED flashes for 0,5 second; the activation of
the Chirp function is signalled by one audible tone.
LED’
S
MEMORY
While alarm disarmed it is possible to verify if an alarm condition has occurred and to determine the cause
following the LED flashing.
LED
SIGNALLING
A
LARM TRIGGERING
Ultrasonic sensors inlet
Ignition live (engine immobilisation)
Door, boot and bonnet pin switch and absorption
sensor.
LED OFF (2,5 seconds)
LED ON ( 400mS)
NOTE
:
to stop the LED flashing it is necessary to turn the ignition key to ON.
ACTIVE FUNCTIONS WHILE ALARM ARMED
I
MMEDIATE
AFTER
45
SECONDS
- Engine immobilisation: activates while arming the
system; the detection is obtained after the neutral
time of 45 seconds.
- cut wires (
art.7203
)
- current absorption;
- door, boot and bonnet opening;
- sensors inlet.
NOTE: the neutral time is signalled through the LED lightning fix.
Transmitters battery discharging
The discharging of the battery is signalled through the LED of
the transmitter. If the LED flashes while pressing one of the
transmitter’s buttons it is necessary to replace the batteries.
Batteries model : CR1616
Note:
put the batteries in the appropriate container.
TECHNICAL DATA
Power supply
12VDC
Current absorption alarm ON with US module
16mA
Current absorption alarm OFF
9 mA
Working temperature
-30°+ 85°C
Engine immobilisation relay contact capacity
8A a 20°C
Blinker and central door locking relay contact capacity
10A a 20°C
Power sound at 1 meter in open space
> 118dB
Minimum sensitivity absorption sensor
5W
Current for positive control alarm armed
500 mA
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 7203 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 7203 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info