589619
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Introduction
WARNING
Read all instructions carefully before installing and using the
Vector system. Improper use could result in serious injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Go to www.garmin.com/vectorowner for the latest information
including bike compatibility, software updates, and video
tutorials.
Thank You
Thank you for your Vector or Vector S purchase. This manual
covers both Vector systems.
Vector was designed for cyclists, by cyclists, to provide an
outstanding experience of owning a precision power
measurement system for your bike.
Vector is simple, accurate, and easy to use.
For software updates, video tutorials, and everything you need
to get years of service out of your Vector, go to
www.garmin.com/vectorowner.
Now it's time to put the power under your feet and get out there
and ride.
Getting Started
1Install the Vector components (Installing the Vector
Components).
2Install the shoe cleats (Installing the Shoe Cleats).
3Pair Vector with your Edge® (Paring Vector with Your Edge
1000).
4Go for a ride (Your First Ride).
5View your history (Vector Data).
6Send your history to your computer (Sending Your Ride to
Garmin Connect).
Tools Needed
15 mm pedal wrench
Bike grease
3 mm hex key
4 mm hex key
Installing the Vector Components
The installation steps for the Vector and Vector S systems are
very similar. Procedures that are specific to the Vector S system
are noted.
Preparing the Crank Arms
1Confirm the compatibility of your bike at www.garmin.com
/vectorowner.
2Remove the existing pedals.
3Clean the threads, and remove old grease.
Determining Pedal Pod Clearance
NOTICE
The pedal pod should contact the crank arm only at its mounting
face, because this is the load-bearing connection. If the pedal
pod contacts the crank arm anywhere else, the pedal pod may
fracture when the pedal is tightened.
If the mounting face À surrounding the threaded hole in the
crank arm is recessed, use one or two washers Á to fill the
recess.
NOTE: Do not use more than two washers.
Make sure the pedal pod mounting face  contacts the crank
arm only at its mounting face (or the washer used to fill the
recess).
If it touches anywhere else, you can use another washer to
provide the necessary clearance.
If it is close, you can confirm proper clearance by sliding a
piece of paper between the metal bracket and the crank arm
face.
If the mounting face of the crank arm is protruding, do not
use washers.
Determining the Bicycle Chain Clearance
Before you can install the right pedal, you must determine
bicycle chain clearance.
Move your bike chain to the largest chain ring and the
smallest cassette gear.
The bike chain should be in the outermost position to
determine proper clearance between the pedal pod cable
and the chain.
NOTE: There must be at least 5 mm clearance À between
the chain and the crank arm.
Installing the Pedal Pod and Pedal
This procedure is for the Vector system. For the Vector S
system, see Installing the Left Pedal and Pedal Pod.
NOTE: The left and right pedal pods are the same.
1Install the left pedal first.
2Apply a thin layer of grease on the pedal spindle À and the
pedal pod Á where it contacts the pedal spindle.
Introduction 1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Vector bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Vector in de taal/talen: Engels als bijlage per email.

De handleiding is 3,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Vector

Garmin Vector Snelstart handleiding - English - 26 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info