589620
2
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
Vector Quick Start Manual
WARNING
Read all instructions carefully before installing and using the
Vector system. Improper use could result in serious injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Go to www.garmin.com/vectorowner for the latest information
including bike compatibility, software updates, and video
tutorials.
Tools Needed
15 mm pedal wrench
Bike grease
3 mm hex key
4 mm hex key
Installing Vector Components
Preparing the Crank Arms
1Confirm the compatibility of your bike at www.garmin.com
/vectorowner.
2Remove the existing pedals.
3Clean the threads, and remove old grease.
Determining Pedal Pod Clearance
NOTICE
The pedal pod should contact the crank arm only at its mounting
face, because this is the load-bearing connection. If the pedal
pod contacts the crank arm anywhere else, the pedal pod may
fracture when the pedal is tightened.
If the mounting face À surrounding the threaded hole in the
crank arm is recessed, use one or two washers Á to fill the
recess.
NOTE: Do not use more than two washers.
Make sure the pedal pod mounting face  contacts the crank
arm only at its mounting face (or the washer used to fill the
recess).
If it touches anywhere else, you can use another washer to
provide the necessary clearance.
If it is close, you can confirm proper clearance by sliding a
piece of paper between the metal bracket and the crank arm
face.
If the mounting face of the crank arm is protruding, do not
use washers.
Installing the Pedal Pod and Pedal
NOTE: The left and right pedal pods are the same.
1Install the left pedal first.
2Apply a thin layer of grease on the pedal spindle À and the
pedal pod Á where it contacts the pedal spindle.
3On the pedal spindle, stack the pedal pod and any required
washers Â.
TIP: You must carefully bend the cable à out of the way.
4Insert the spindle into the crank arm Ä.
5Hand tighten the spindle.
NOTE: The left pedal spindle has a left-handed (reverse)
thread.
TIP: Power and cadence calculations are not impacted by
the orientation of the pedal pod. Garmin® recommends
placement of the pedal pod on the leading edge of the crank.
When the crank is in the forward position, the pedal pod
should be pointing downward.
6Rotate the crank arm to check for clearance.
The pedal pod should not interfere with any part of the bike.
7Use the pedal wrench to tighten the spindle.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to
40 N-m).
8Firmly plug the cable into the spindle.
9Rotate the crank arm to check for clearance.
10Repeat steps 2–9 to install the right pedal.
NOTE: If the pedal pod cable rubs the chain, you can add
one or two washers between the pedal pod and the crank
arm to increase clearance.
Installing the Shoe Cleats
NOTE: The left and right cleats are the same.
1Apply a thin layer of grease on the cleat bolt threads.
2Align the cleat À, washers Á, and bolts Â.
3Use a 4 mm hex key to loosely attach each bolt to the sole of
the shoe.
4Adjust the cleat to the shoe in your preferred position.
This can be adjusted after a trial ride.
5Tighten the cleat firmly to the shoe.
NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-
m).
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Vector S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Vector S in de taal/talen: Engels als bijlage per email.

De handleiding is 2,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Vector S

Garmin Vector S Gebruiksaanwijzing - English - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info