740402
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
The device should be mounted at least 1 m (40 in.) away
from cables carrying radio signals such as VHF radios,
cables, and antennas.
For Single Side Band (SSB) radios, increase the distance to
2 m (6 ½ ft.).
Mounting the Radar
Before you mount the radar, you must review the mounting
location considerations and select a mounting location.
NOTE: The supplied M8 x 1.25 x 60 threaded rods can be used
on mounting thicknesses of 5 to 30 mm (
3
/
16
to 1
3
/
16
in.)
(recommended). For surfaces over 30 mm (1
3
/
16
in.), use longer
threaded rods.
1
If you are not installing the device on a pre-drilled Garmin
compatible radar mount, use the included mounting template
to drill four 9.5 mm (
3
/
8
in.) mounting holes.
2
Connect the power cable to the power port and the
network cable to the network port .
3
Press the cables into any of the guide grooves on the
bottom of the case, and secure them using a cable hold-
down plate .
The cables should be bent or twisted as little as possible.
4
Using the arrow on the bottom as a reference, position the
radome on the mounting surface aligned to the front of the
vessel.
NOTE: If you choose not to align the dome with the front of
the vessel, you can adjust the front-of-boat offset after the
dome is installed (Setting the Front-of-Boat Offset,
page 3).
5
Apply the included anti-seize compound to the threads of the
four M8 x 1.25 x 60 threaded rods.
6
Insert the four threaded rods into the mounting holes on the
bottom of the radome.
Up to 50 mm (2 in.) of the threaded rods may extend below
the radome.
7
Apply a bead of marine sealant on the mounting surface
around each mounting hole.
8
Fasten the radome to the mounting surface using the
threaded rods , flat washers , spring washers , and
hex nuts .
9
Using a torque wrench, tighten the nuts to 13.7 to 18.6 N-m
(10 to 14 lbf-ft.).
Cable Considerations
It may be necessary to drill 32 mm (1
1
/
4
) in. holes for routing the
power or network cables.
When routing both the power and network cables through the
same hole, you must route the network cable before the
power cable.
You must apply marine sealant to the hole after the cables
are in place to ensure a waterproof seal.
If the routing hole must be made in a visible location, decorative
cable grommets can be purchased from Garmin or a Garmin
dealer (optional).
If needed, the grommet can be trimmed to enable you to
route both the network and the power cable through the
same hole.
The optional grommet does NOT provide a waterproof seal.
You must apply marine sealant to the grommet after the
cables are in place to ensure a waterproof seal.
When installing the network and power cables, you should
observe these considerations.
Cutting the Garmin Marine Network cable is not
recommended, but a field install kit can be purchased from
Garmin or a Garmin dealer if cutting the network cable is
necessary.
To ensure safety, appropriate tie-wraps, fasteners, and
sealant should be used to secure the cable along the route
and through any bulkheads or the deck.
Cables should not be run near moving objects and high-heat
sources or through doorways and bilges.
To avoid interference with other equipment, network and
power cables should not be run next to or parallel to other
cables, such as radio antenna lines or power cables. If this is
not possible, the cables should be shielded with metal
conduit or a form of EMI shielding.
The power cable should be installed as close to the battery
source as possible.
If it is necessary to extend the power cable, the
appropriate gauge of wire must be used (Power Cable
Extensions, page 3).
Incorrectly extended runs of cable may cause the radar to
malfunction due to insufficient power transmission.
Connecting the Power Cable
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the power cable from the device to the power source.
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin GMR Fantom 24 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin GMR Fantom 24 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin GMR Fantom 24

Garmin GMR Fantom 24 Installatiehandleiding - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info