740407
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Installation Procedures
Preparing the Radar Mounting Surface
Before you can mount the radar, you must choose a suitable
mounting location (Mounting Considerations, page 1).
1
Secure the included mounting template to the surface at the
mounting location, along the bow-stern axis, as indicated on
the template.
2
Drill the mounting holes using a 15 mm (
19
/
32
in.) drill bit.
3
If you need to run the power and network cables through the
mounting surface, select a location along the center channel
indicated on the template, drill a pass-through hole for the
cables using a 32 mm (1
1
/
4
in.) drill bit, and route the cables
through the surface (optional) (Wiring and Connection
Considerations, page 2).
4
Remove the mounting template from the surface.
Mounting the Radar
Before you can mount the radar, you must select a mounting
location (Mounting Considerations, page 1) and prepare the
mounting surface (Preparing the Radar Mounting Surface,
page 2).
1
Place the radar onto the mounting surface, aligning the holes
on the base of the radar with the holes you drilled when
preparing the mounting surface.
2
Apply the included Petrolatum Primer to the threads of the
four threaded rods.
3
Insert the threaded rods through the mounting surface and
into the radar base, and tighten them using a 5 mm hex
wrench.
To avoid damaging the pedestal, you should stop tightening
the threaded rods when they no longer turn easily.
4
From under the mounting surface, place the included plastic
shoulder washers over the threaded rods and into the
holes.
5
Place the flat washers , lock washers , and hex nuts
on the threaded rods.
6
Tighten the hex nuts to a torque of 14.7 N-m (11 lbf-ft.) to
securely fasten the radar to the surface without damaging the
radar or the mounting hardware.
Installing the Antenna
Before you can install the antenna on the radar, you must
securely mount the pedestal (Mounting the Radar, page 2).
1
Remove the protective cover from the waveguide on the
top of the pedestal.
2
Align the waveguide on the pedestal with the socket on
the bottom of the antenna , and slide the antenna onto the
pedestal.
3
Secure the antenna to the pedestal by tightening the captive
hex bolts under the antenna arm.
4
Tighten the hex bolts to a torque of 7.9 N-m (6 lbf-ft.) to
fasten the antenna to the pedestal without damaging the
antenna or the mounting hardware.
Wiring and Connection Considerations
It may be necessary to drill 32 mm (1
1
/
4
in.) holes for routing the
power, network, or grounding cables.
When routing multiple cables through the same hole, you
must route the network cable before the power and ground
cables because of the size of the network connector.
You must apply marine sealant to the hole after the cables
are in place to ensure a waterproof seal.
If you must make the routing hole in a visible location,
decorative cable grommets can be purchased from Garmin or a
Garmin dealer (optional).
If needed, you can trim the grommet to enable you to route
multiple cables through the same hole.
The optional grommet does NOT provide a waterproof seal.
You must apply marine sealant to the grommet after the
cables are in place to ensure a waterproof seal.
When installing the cables, you should observe these
considerations.
Cutting the Garmin Marine Network cable is not
recommended, but a field install kit can be purchased from
Garmin or a Garmin dealer if you must cut the network cable.
The ground cable is not included, and must connect to a
water ground location, not the negative terminal of the battery
(Grounding the Radar, page 3).
To ensure safety, appropriate tie-wraps, fasteners, and
sealant should be used to secure the cable along the route
and through any bulkheads or the deck.
You should not run cables near moving objects and high-heat
sources, or through doorways and bilges.
To avoid interference with other equipment, you should not
run network and power cables parallel to other cables, such
as radio antenna lines or power cables. If this is not possible,
the cables should be shielded with metal conduit or a form of
EMI shielding.
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin GMR Fantom 126 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin GMR Fantom 126 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin GMR Fantom 126

Garmin GMR Fantom 126 Installatiehandleiding - Nederlands - 6 pagina's

Garmin GMR Fantom 126 Installatiehandleiding - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info