691444
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2
Connect the bare-wire end of the power cable to a 12 Vdc
power source and to ground.
3
Align the notch on the end of the power cable with the power
port on the device, and press the cable into place.
4
Tighten the locking ring.
5
Repeat steps 3 and 4 for the network and transducer cables.
Installation Diagram
You can use this diagram to identify the connection points from
your sounder to the network, power, and transducer.
Item Description
À
Chartplotter
Á
GCV 10
Â
Power Source
Ã
Transducer
Cable Routing Grommets
NOTICE
Cable routing grommets do not create a waterproof seal. To
create a waterproof seal, apply a marine sealant around the
grommet and cable after installation. Be sure to test the system
before sealing the grommets.
When routing cables through your boat, it may be necessary to
drill holes to route the connector ends of the cables. A rubber
grommet is provided to cover the cable hole for a finished look.
You can purchase additional grommets from your Garmin
dealer or directly from Garmin at www.garmin.com.
Installing the Cable Grommet
1
Mark the location where you want to route the cable.
2
Using a 32 mm (1¼ in.) paddle drill bit or hole saw, drill the
installation hole.
3
Route the cable through the hole to the sounder.
4
Spread the grommet apart at the split, and place it around
the cable.
5
Firmly push the grommet into the installation hole until it is
seated.
6
Apply marine sealant, as needed, to weatherproof the
installation hole.
Blink Codes
After the sounder is installed, it turns on when the chartplotter is
turned on. The two-color (green and red) LED on the sounder
indicates its operational status.
LED
Color
State Status
Green Slow blink The sounder is connected to a chartplotter
and is operating properly. You should see
sonar data on the chartplotter.
Red Slow blink The sounder is turned on, but is not
connected to a chartplotter, or is waiting to
connect to a chartplotter. If the sounder is
connected to the chartplotter and this code
persists, check the wiring connections.
Red/
Green
Slow blink The sounder is in test mode.
Red Rapid blink
sequence
System error. The chartplotter displays a
message indicating the type of failure. When
the error condition is fixed, the sounder must
be completely disconnected from and
reconnected to its power source to clear the
error.
Specifications
Specification Measurement
Size (H×W×D) 251 x 192 x 66 mm (9.9 x 7.6 x 2.6 in.)
Weight 845 g (1.86 lb.)
Case Material Fully gasketed, polycarbonate plastic, water
resistant to IEC 60529-IPX7
Temperature Range From -15° to 70°C (from 5° to 158°F)
Power Input From 10 to 35 Vdc
Power usage 10.5 W maximum
Fuse 4.0 A, mini 42 Vdc, fast-acting, blade-type
Compass Safe
Distance
260 mm (10.2 in. )
Transmit Power (RMS)* 500 W per element (1,500 W combined)
*dependent upon transducer rating and depth
Frequency 455/800 kHz
Depth** 229 m (750 ft) down; 153 m (500 ft) side
**maximum depth, dependent upon
transducer, water salinity, bottom type, and
other water conditions
Data Output Garmin Marine Network
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin GCV10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin GCV10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin GCV10

Garmin GCV10 Installatiehandleiding - Nederlands - 4 pagina's

Garmin GCV10 Installatiehandleiding - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info