747962
2
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
90˚
(Antenna installation)
Connector   
The direction of the connectors of the bottom 3 ports is
GLIIHUHQWE\Û
56%
&+6HUYRV
6%86VHUYRV
6%86*\URV
5HFHLYHUق6HUYRك%DWWHU\$
HJ/LSRFHOO岜9
5HFHLYHUق6HUYRك%DWWHU\%
HJ/LSRFHOO岜9
+XE
+XE
([FOXVLYHVZLWFK
6%86HTXLSPHQW
7HOHPHWU\VHQVRU
7HOHPHWU\VHQVRU
6%86
3RUW
6%86
3RUW
D
G
D
G
'RQRWFRQQHFW
DEDWWHU\WR
WKHSRUWVDW
WKLVVLGH
%DWWHU\
FRQQHFWRU
Do not use a battery of the
wrong rated voltage and
type (Li-po, Li-Fe, etc.).
When the receiver is not in
use, always disconnect the
battery.
WARNING
Never reverse the battery polarity.
A reverse connection the battery terminals may cause
abnormal heating, fire and burns.
Do not short circuit the battery terminals.
A short circuit across the battery terminals may cause
abnormal heating, fire and burns.
Be careful when soldering to the plug; don't overheat
the plug with your soldering iron and take great care to
avoid short-circuits on the plug.
Such a overheat and short-circuit would destroy the plug.
LED Indication
System Mode LED Status Link LED
FASSTest Green Solid
No signal reception Red Solid
Receiving signals Green Solid
Waiting for link
Start 2second later Red
Blink(1second)
FASST Off
No signal reception Red Solid
Receiving signals Green Solid
Receiving signals but ID is unmatched Green Blink
Waiting for link Red Blink
FASSTest
FASST
Unrecoverable error (EEPROM, etc.)
Alternate blink
*Fixed at neutral if a servo is connected to a port other than a usable
transmitter channel.
*The telemetry and Extra Voltage ports cannot be used with the
FASST system.
FASSTest FASST (Normal-High-speed
Change method
1
. Turn on the receiver.
Transmitter OFF
2
. Press and hold the Link/Mode button for more then 5 second.
3
. When the LED begins to blink green/red the button may be
released.
4
. The LED should now be blinking red in one of the patterns
described by the chart below.
( Default : FASSTest )
5
. Each press of the Mode/Link button advances the receiver to
the next mode.
6
. When you reach the mode that you wish to operate in, press
and hold the Mode/Link button for more than 2 seconds.
7
. Once locked into the correct mode the LED will change to a
solid color.
8
. Please cycle the receiver(s) power off and back on again
after changing the Channel Mode.
Red LED blink System
1 time FASSTest
2 time
FASST Multi-ch
Normal mode
3 time
FASST Multi-ch
High-speed mode
Connection
Female Deans Ultra Plug
Soldering
Battery Wire
Heatshrink
tube
- 2 -
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba R7018SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba R7018SB in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Futaba R7018SB

Futaba R7018SB Gebruiksaanwijzing - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info