747950
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2017, 1 (1)
WARNING
Do not insert or remove the S.BUS connector while
the receiver power is ON.
Since the S.BUS servo switches the operation mode automatically
according to the type of signal (S.BUS signal/PWM signal) from the re-
ceiver, if the connector is inserted or removed while the power is ON, an
S.BUS connected servo will be erroneously recognized and may stop.
WARNING
Turn on the power on transmitter receiver in order.
In addition, always check the operation of all the func-
tions before flight.
What is S.BUS?
Different from conventional radio control systems, the S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other S.BUS compatible
devices. This data includes commands such as “move the
channel 3 servo to 15 degrees, move the channel 5 servo to
30 degrees” to multiple devices. The S.BUSGHYLFHVH[HFXWH
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
/LQNWRWKHWUDQVPLWWHU
Easy Link ID allows T-FHSS Air receivers to link to
compatible transmitter without pressing the link button on the
receiver.
1
Bring the transmitter and the receiver close to each
other, within 20 inches (half meter).
2
Turn on the transmitter. Place the transmitter into the
receiver linking mode.
3
Turn on the receiver.
4
The receiver will wait for the linking process to begin
for 3 seconds. Following that it will return to the
normal operation mode.
5
When the LED of the receiver changes from blinking
red to solid green, linking is completed.
(A link waiting state is ended in 3 second.)
* Refer to the transmitters operation manual for complete details on how
to place the transmitter into the linking mode.
WARNING
Do not perform the linking procedure while the mo-
tor's main wire connected or the engine is operating as it
may result in serious injury.
When the linking is complete, please cycle the receiv-
er power and ensure the receiver is properly linked to the
transmitter.
Please power up your system in this order. Transmit-
ter first, followed by the receiver.
If the R3001SB receiver was previously linked to an-
other transmitter, make sure that transmitter is not oper-
ating while linking the receiver to the new transmitter.
* If there are many T-FHSS Air systems turned on in close proximity,
your receiver might have difficulty establishing a link to your transmit-
ter. This is a rare occurrence. However, should another T-FHSS Air
transmitter/receiver be linking at the same time, your receiver could
link to the wrong transmitter. This is very dangerous if you do not no-
tice this situation. In order to avoid the problem,we strongly recom-
mend you to double check whether your receiver is really under con-
trol by your transmitter.
* If the System Type of the transmitter is changed, the receiver will need
to be re-linked to the transmitter.
* Link is required when a new model is made from a model selection.
&KDQQHO0RGHV6%86
CH3)
The R3001SB is capable of changing its channel allocations
as described in the table below.
1
Turn on the receiver. (At this moment, the transmitter
should be off.) Then, LED blinks RED in about 3
seconds. Next, wait until it becomes solid RED.
2
Press and hold the Mode switch more than 5
seconds.
3
Release the button when the LED blinks RED and
GREEN simultaneously.
4
The receiver is now in the "Operation CH Set" mode.
At this moment, the LED indicates current set sta-
tus through flashing a pattern that corresponds to the
CH mode.
&DQQRWH[LWWKLV&+VHWWLQJPRGHEHIRUHWKHRSHUDWLRQPRGHLV
¿[HG
6HHWKHQH[WWDEOHWKDWVKRZVFRUUHVSRQGHQFHEHWZHHQ&+PRGH
DQGZD\RIÀDVKLQJ/('
'HIDXOW&+PRGHLV0RGH%
5
By pressing the Mode switch, the operation CH is
switched sequentially as " Mode B" "Mode A" "Mode
B"....
Mode A Mode B
3/S.BUS 3CH S.BUS
Red LED blink 1 time 2 time
R3001SB CH Mode table
Default CH mode
6
The operation mode will be set by pressing the Mode
switch more than 2 seconds at the desired CH
mode.
7
Release the button when the LED blinks RED and
GREEN simultaneously. Then, the operation CH is
fixed.
8
After confirming the operation CH mode is changed,
turn off and back on the receiver power.
*The “Operation CH Set” mode cannot be changed during the
receiver communicates to the transmitter.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba R3001SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba R3001SB in de taal/talen: Engels als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info