747977
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
WARNING
Failure to follow these safety precautions may result in severe injury to
yourself and others.
Check that there is sufficient battery capacity.
Do not operate the model and transmitter steering wheel
for about 3-5 seconds after turning on the GYD450 (When
shared with the receiver).
• GYD450 initialization and neutral position reading. The GYD450 is initialized when the
power is turned on. The neutral position is also read at the same time. If initialization
ends normally, the operator is informed by two repetitive movements of the servo to
the left and right (a little).
Always check the direction of operation of the gyro.
Do not strike the gyro with a hard object. Do not drop it onto
a concrete surface or other hard floor.
• The sensor may become damaged during strong impacts.
Do not use trims or mixing.
• All corrections are made by the gyro. Therefore, if trimming and mixing, are turned on,
operation will be the same as deviating from the neutral position.
Do not use the GYD450 for applications other than RC cars.
•This gyro is designed for RC cars only. Do not use it for other applications.
Analog servos cannot be used.
•The use of analog servos may cause servo trouble.
Do not place gyro near heating equipment (engine, motor,
ESC, battery, servo, etc.).
Always allow the gyro to adjust to the surrounding environmental temperature before
ÀLJKW$ODUJHWHPSHUDWXUHFKDQJHGXULQJXVHZLOOFDXVHGULIWDQGRWKHURSHUDWLRQDO
issues.
Connecting the GYD450 S.BUS Connecting the GYD450
Mounting to Chassis
Steering servo SR mode
Rate Gyro
for RC Drift Cars
I
NSTRUCTION
M
ANUAL
I
NSTRUCTION
M
ANUAL
Only for Futaba digital servo
For RC models
Gyro
Included sponge
sensor tape
Degrease
and stick
Horizontal plane
Flat surface of the chassis where the sensor
tape sticks easily. Mount the gyro level so
that it is not tilted relative to the chassis.
Use the included double-sided sponge tape to firmly at-
tach the gyro perpendicular to the control axis, at a posi-
tion where there is as little vibration as possible. Make the
Gyro mounting position
The direction of rotation fixed by the gyro can be any
direction within 360° relative to the steering axis controlled
by the gyro.
• No part of this manual may be reproduced in any form without prior permis-
sion.
• The contents of this manual are subject to change without prior notice.
• Futaba is not liable for any potential damage (accidental or otherwise) that
may occur after installation.
Before using your new gyro, please read this manual thoroughly and
use the gyro properly and safely. After reading this manual, store it in
a safe place.
● Dedicated RC Drift car setting
Vehicle straight-line and cornering performance can be increased without
taking into account the effect of the road surface, etc.
● Remote gain function and mode switching function
You can adjust gain from the transmitter (3 or more CH) by using the
remote gain function. Gain can also be adjusted with the trimmer on the
GYD450. The mode switching function allows AVCS/NORMAL gyro mode
switching.
● Integrated, compact, and light weight
Compact size
20.5x20.5x11mm
and light weight
3.7g
realized by
high density mounting technology.
● Easy setup
The GYD450 can be used immediately with minimum setup.
● Supporting the S.BUS/S.BUS2 connection
Only one wire connection to the receiver can operate the GYD450.
● Only for Futaba digital servo
GYD450 Ratings:
(Integrated sensor type rate gyro)
Gyro sensor: MEMS vibrating structure gyro
Operating voltage: DC4.2V to 8.4V
Current drain: 30mA (excluding a servo)
Operating temperature range: -10ºC to +45ºC
Dimensions: 20.5 x 20.5 x 11.0mm (0.8 x 0.8 x 0.43in) (except protrusion)
Weight: 3.7g (0.13oz)
Functions: Sensitivity trimmer. LED monitor. Servo selection (SR mode
ON/OFF). S.BUS/S.BUS2 connection.
Features of GYD450
Functions
Monitor LED display
State Color Move Reference
1. No servo pulse / sensor
error
Red 2 flash
2. Warm-up Green Fast blink
3. Sensor initialization Red/Green ON
AVCS (Red)
NORMAL (Green)
4. Turn Red/Green Fast blink
Right (Green)
Left (Red)
5. Neutral offset Orange Slow blink Stick operation
6. Gain OFF
OFF
7. Switch operation Green One blink
Each time of switch
operation
8. Low battery Red One flash Less than 4.0V
Trimmer
Limit/Gain
LED
Servo selection switch
(SR mode ON/OFF)
Port1
Steering input/
S.BUS input
Port2
Gain input
Port3
Steering servo output
Gyro direction
Switch
Set Contents
The following items are supplied with the GYD450:
Mini screwdriver
Sensor tape
Extension cord
Nylon strap
GYD450
1M23N33302
Thank you for purchasing the
GYD450 RC cars gyro. Compact
and lightweight, the GYD450 is
designed to control steering for RC
Drift cars. If the transmitter has 3
or more channels (capable of 3CH
adjustment) the gyro sensitivity can
be adjusted from the transmitter.
Features include simple set-up and
S.BUS/S.BUS2 connectivity.
S.BUS/S.BUS2 port
GYD450 GYD450
S.BUS Receiver
Steering servo Steering servo
Steering CH1
Gyro gain CH3
Receiver
Gyro gain CH(Receiver)←connect→Port2(GYD450)
Remote gain effective. Trimmer(GYD450) becomes LIMIT.
Gyro gain CH(Receiver)←It does not connect→Port2(GYD450)
Remote gain is invalid. Trimmer(GYD450) becomes GAIN.
S.BUS CH
Steering --- 1CH
Gyro gain --- 3CH
Extension cord
In S.BUS
connection, the
port 2 is not
connected.
Remote gain is still
effective.
wiring loose and bundle it with the included nylon strap so
that it will not interfere with the rod.
Link the servo in accordance with the kit instruction man-
ual. Adjust the linkage rod so that the trim amount is as
small as possible.
When using S.BUS servo, initialize a parameter.
Make the servo operating range as wide as possible.
Make the numerical value of EPA (ATV) equally in left and
right.
It is possible when using the T7PX to change the servo to
"SR Mode" and improve the servo response. If the servo
can't be changed to SR mode, do not set the TX to SR
mode.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba GYD450 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba GYD450 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info