747972
4
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
4
R
EPLACEMENT &
O
PTIONAL
I
TEMS
Futaba PC Interface CIU-2: FUTM0951
Extension 200 mm:
Extension 350 mm:
Extension 55 mm:
Extension 80 mm:
Extension 130 mm:
Mounting Pad:
1x22x22 mm (10)
WARNING
Newer high end servos and other radio equipment
are capable of placing large demands on the power
systems in use today. When using a regulator you
must ensure that the regulator is capable of supply-
ing the current demands of the equipment you have
selected. In addition to this make sure the wiring
and switch you have selected are capable of han-
dling high current draws.
The servo current draw can be up to 50% higher on a flybar-
less helicopter. Always ensure your receiver battery is fully
charged before each flight.
Even though the CGY750 is a high performance
gyro and governor, it will be necessary to ensure
that the helicopter mechanics are also in optimum
operating condition. Please use the guidelines be-
low and address all issues before installing and fly-
ing the CGY750.
The CGY750 must be used with a rigid tail rotor drive system.
Any modern torque tube or belt drive system should be ad-
equate. Do not attempt to fly the CGY750 using a wire driven
tail rotor system.
• Always ensure the drive gears, torque tube, pulleys, belt,
bearings and shafts are in proper working condition. If any of
these items are damaged or worn they must be replaced.
The linkage rod, tail rotor bell crank, pitch slider and tail rotor
grips must operate without friction to obtain the best perfor-
mance from the CGY750. Binding in the tail rotor control linkage
will decrease the performance of the CGY750 gyro and this may
also shorten the servo lifespan. Please take the time now to en-
sure the tail rotor system on your helicopter is working correctly
and without friction or binding.
Vibration will affect the CGY750’s overall performance. All
rotating components on the helicopter should be balanced
to minimize vibrations in flight. Ensure that your engine or
electric motor is running smoothly and that all vibrations have
been addressed before installing and test flying the CGY750.
Gyro sensor replacement:
• Each CGY750 gyro control box is calibrated specifically for
the gyro sensor included. Do not attempt to use another
CGY750 sensor with the control box as performance will suf-
fer due to being out of calibration. The calibration process
must be completed by an authorized service center.
If your sensor needs replacement, please send the complete
unit to your region’s support center for repair.
7KH J\URVHQVRU VKRXOG EH PRXQWHGRQ D ULJLG SODWIRUPDW OHDVWLQ
>PP@ DZD\ IURPD1LWUR(QJLQH,WLVQRWQHFHVVDU\WRPRXQW
WKHJ\URQHDUWKHPDLQVKDIWRIWKHKHOLFRSWHUEXWLWLVYHU\LPSRUWDQW
WKDWWKHPRXQWLQJDUHDFKRVHQLVULJLG3OHDVHUHIHUWR\RXUKHOLFRSWHU
PDQXIDFWXUHUVLQVWUXFWLRQVIRUUHFRPPHQGHGPRXQWLQJORFDWLRQV
7HVW¿WWKHJ\URVHQVRUHQVXULQJWKDWWKHVHQVRULVLQDOLJQPHQWZLWK
WKHKHOLFRSWHURQWKHUROODQGSLWFKD[LV7KHFDEOHIURPWKHJ\URVHQ-
VRUPXVWH[LWWRZDUGWKHIURQWRUWKHUHDURIWKHKHOLFRSWHUVLQFHWKLVLV
WKHSLWFKD[LV$Q\PLVDOLJQPHQWZLOOFDXVHDORVVRISHUIRUPDQFH
2QFH\RXDUHFHUWDLQHYHU\WKLQJLVSURSHUO\DOLJQHGDQGWKDWWKHVHQVRU
OHDGFDQ EH URXWHG WRWKH J\UR JRDKHDG DQG PRXQWWKHJ\UR VHQVRU
WRWKHKHOLFRSWHUXVLQJRQHRIWKHVXSSOLHGJ\URSDGV5RXWHWKHJ\UR
VHQVRUOHDGWRWKH&*<FRQWUROER[DQGSOXJWKHOHDGLQWRWKHJ\UR
VHQVRUSRUW9HULI\WKDWWKHFRQQHFWRULV¿UPO\ORFNHGLQSODFH
Gyro Sensor
Elevator (Pitch) axis
Rudder (Yaw) axis
• Aileron (Roll)
axis
G
YRO
S
ENSOR
I
NSTALLATION
Important: The CGY750 gyro sensor must be mounted so that the
roll and pitch sensing axis are in alignment with the helicopter. Any
misalignments over 1/2 of a degree will cause a loss in performance.
Please take extra care in this step to ensure the optimum flight perfor-
mance.
TROUBLESHOOTING
If any issues are noted during flight (such as drifting, inconsistent hold
or inconsistent control rates) then please review the following trouble-
shooting recommendations.
1. Always verify that the tail rotor and swash plate mechanisms oper-
ate, and that the drive system is in proper working order.
2. Electromagnetic interference could be causing the problem. If you
feel everything is set up correctly and that the helicopter is vibration
free, then consider moving the gyro sensor to a new location away
from servos, ESC and drive motors.
3. Vibrations will decrease the performance of all gyro systems. Even
though the CGY750 gyro sensor is the most vibration resistant gyro
sensor available, eliminating vibrations will always improve perfor-
mance. The CGY750 gyro sensor performs best when the sensor is
mounted rigidly to the airframe. This is mainly due to the sensing of
all 3 axes. It is highly recommended to avoid using soft foam pads
as this may allow the gyro to bounce around on the roll and pitch
axis, causing instabilities and possible loss of control during flight.
The bottom of the CGY750 Gyro
Sensor must be perpendicular to
the main shaft.
The roll axis must be parallel to
the tail boom and the pitch axis
must be perpendicular to the side
frame.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba CGY750 V 2.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba CGY750 V 2.0 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info