29013
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Neck strap bracket
Bracket for neck strap. (Neck strap is sold separately.)
Antenna
Strong
telescoping
antenna. Extend
it
to
its
full
length
when using the transmitter.
Handle
Use this bar to carry the transmitter.
Nonslip adjustable lever head
The length of the lever head can be adjusted to suit the
operator.
in the arrow direction, and adjust the head to
the most comfortable length, then lock it by
turning it in the direction opposite the arrows. Fig. 3
and
, by turning them
Lever head
Lever head
Unlock lever heads
Charging jack
Use this jack for charging.
Transmitter crystal
Battery cover
18 Servo reversing switches
Using the servo reversing switches
The left side of each switch is the normal position.
The servo reversing switches reverse the direction of opera-
tion of the servos.
Adjust to the length of your hand.
Charging of transmitter and receiver Nicad batteries
Recharge the receiver and transmitter Nicad batteries as
shown in Fig. 4.
Fig.
5
Aileron servo
reversing switch
NORM-> Normal
REV-> Reverse
After linkage is complete, inspect the servos. If the direction of
operation of the stick lever and the direction of operation of a
servo are opposite, switch the appropriate servo reversing switch.
Rudder servo
reversing switch
Throttle servo
reversing switch
Elevator servo
reversing switch
Connect the charging plug of the dual charger to the trans-
mitter charging jack. Connect the Rx-connector of the dual
charger to the receiver Nicad battery plug, and AC-plug the
dual charger to AC-outtet socket as shown in the figure.
The receiver battery can be used about 10 times at 10 min-
utes per flight between rechargings.
Charge the batteries for about 15 hours. When the set is not
in use for some time, repeat discharge and charge two to
three times before use. (If the batteries are not used for a
long time, their capacity will go down).
The dual charger transmitter and receiver Nicad batteries
independently or simultaneously.
Notes
1) First connect the charger to the transmitter charge jack.
The LED on the charger will glow RED.
2) Next connect to the receiver switch harness charge cord.
The LED will change to GREENISH-RED (ORANGE).
3) In the case where only one battery pack is connected, the
LED color will be:
TXonly: GREEN
RXonly: RED
Nicad Battery
Connector
Caution
Do not pull the Nicad battery
connector when the back cover
is removed. The power switch
may be damaged if the battery
connector is strongly pulled.
Use a small Phillips
screwdriver
Charger PBC-8B
LED
Charging plug
for transmitter.
AC-plug.
Rx
Tx
Transmitter
Nicad battery
NT-8JY
Battery cover
NR-4QB
Fig.
4
Elevator
Aileron
Rudder
The tension of the stick lever spring can be adjusted.
When these screws are
removed, the back cover
can be removed.
•The tension of the
spring can be ad-
justed by removing
the transmitter back
cover and turning
the screw for each
stick. Set the springs
for the best stick feel.
Fig.
6
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba ATTACK_4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba ATTACK_4 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info