522198
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
In a new installation, mechanical stops can be installed after
the cylinder. For retro-t applications, use Figure 4.1 as a ref-
erence to ensure the ends of the cylinder travel are outside the
stops. Mount cylinder with the ttings in the up direction.
4.2 HYDRAULIC
The unit is shipped full of oil with a sealed plug in the top of the
reservoir cover. A vented breather cap is supplied with the unit.
The vented cap must be installed in place of the plug after the
drive unit has been mounted. The oil in the LA17 is standard
hydraulic oil (ISO-32).
If the hydraulic lines are removed during installation, be sure to
cap them to minimize the loss of oil. Located on the top of the
valve/reservoir block is a small bleed tting. This tting can be
used add oil to the port and starboard lines or bleed air from
the system. If the cylinder is mounted properly, the cylinder
can be manually stroked and the air will collect at the bleed
tting. Be sure to re-install this plug before using the LA17 as
it is part of the steering line.
The oil reservoir should be maintained at least 3/4 full. During
bleeding and lling this level should be maintained.
It is not critical to identify which of the steering lines is port
or starboard as most new autopilots will determine the pump
direction and program the drive outputs to suit. For older au-
topilots the motor leads can be reversed to change the pumps
direction.
4.3 ELECTRICAL
The motor is a permanent magnet style motor, ignition pro-
tected, built to conform to UL-1500 and SAE-1171 standards.
Two leads connect to the autopilot pump driver junction box
(processor), the direction of the pumpset can be reversed by
simply reversing the polarity of these two leads.
The solenoid valve is connected to the autopilot junction box.
It is usually referred to as clutch/bypass or switched power.
The polarity of the solenoid valve does not matter.
To test the operation of the LA17 pumpset, touch the two leads
from the motor to the supply voltage (12 VDC or 24 VDC) to jog
the motor in one direction and then reverse the leads to jog the
pumpset in the other direction. Do not to perform this opera-
tion where any combustible fumes exist.
p06
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno LA 17 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno LA 17 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info