540715
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
6
Conditions and precautions for using the
cables are as follows:
zUSB cable
-Use the supplied USB cable.
-When connecting to a USB hub, make sure
to use the USB hub that is connected to the
USB port of the computer.
-If you connect the scanner with USB 2.0, it
is required that the USB port and the hub be
compliant with USB 2.0. The scanning
speed slows down when you connect the
scanner with USB 1.1.
-Connect it with the
USB mark facing up.
zSCSI cable
-SCSI cable and SCSI card need to be
purchased separately.
SCSI cable
A 50-pin half-pitch connector is required on
the scanner side, and the other end of the
cable must fit the SCSI card connector on
the computer.
SCSI card
Use one of the recommended SCSI cards
from the following website:
http://www.fujitsu.com/
-In a SCSI daisy chain formation, connect
the scanner so that it is the last device on
the chain.
-Be careful not to damage the connector pins
when connecting to the computer.
-The SCSI ID is set to "5" at factory default. If
the same ID is used by another device, dial
the SCSI ID switch to a different setting.
0 to 7: Available
8, 9 : Set to factory default (SCSI ID=5)
3. Connect the AC cable to the AC adapter
(hereinafter called the "power cable").
4. Connect the power cable to the power
connector of the scanner and the power
outlet.
Test-Scan
Use ScandAll PRO to confirm that documents can
be scanned correctly.
Perform a test in the following procedure.
1. Press the [Power] button on the operator
panel.
D The scanner is turned on, and the [Power]
button lights in green.
During initialization, the Function Number
Display changes as follows: "8" J "P" J
"0" J "1". The scanner is ready when "1"
is displayed.
2. Turn on the computer.
D The scanner is automatically detected.
WARNING
Only use the supplied power cable.
To prevent electrical shock or scanner
malfunction, do not perform the following:
zUse a different power cable
zUse the supplied power cable for other
devices
USB mark
When you plug the cable into the
outlet, the [Power] button on the
scanner’s operator panel will flash
once. Note that this is an initial
diagnosis and not a malfunction.
If "1" is not displayed on the Function
Number Display, refer to "Chapter 8
Troubleshooting" in the Operator's
Guide.
When you press the [Power] button,
the LED indicator will flash once.
Note that this is an initial diagnosis
and not a malfunction.
If the [Found New Hardware] dialog
box appears, select [Locate and install
driver software (recommended)], and
follow the instructions on the screen to
install the driver.
Check
Function
Send to
Scan
/Stop
Power
Function
Number
Display
[Power] button
LED indicator
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fujitsu Fi-6230Z bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fujitsu Fi-6230Z in de taal/talen: Engels als bijlage per email.

De handleiding is 1,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info