631063
5
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
g
3
S
PRODUCT DESCRIPTION (Fig. 0)
1. Supply cord retainer
2. Rear handle
3. Assist handle lock buttons
4. Air vents
5. Debris shield
6. Cutting line head
7. Edging guide / line protector
8. Motor housing
9. Adjustable shaft
10. Shaft locking button
11. Assist handle
12. On/Off trigger
13. Mains cable
a
SAFETY MARKINGS
The following symbols on your trimmer are intended to remind you of some of the most important
safety precautions:
1. WARNING. This product is potentially dangerous. Take great care at all times to avoid injury.
2. Read the operator’s manual.
3. Disconnect the mains plug if the cord is damaged.
4. Wear eye protection at all times.
5.
Approved ear defender.
6. Do not work near bystanders.
7. Do not use in rain or damp conditions.
8. LWA indicates the noise power level. Wear ear plugs or mufflers if necessary.
9. indicates that the product conforms to the relevant European Directives as required by law.
b
ASSEMBLY
DEBRIS SHIELD INSTALLATION
Fig. 2-1
1. Position the motor housing with string head carrier facing up.
2. Slide debris shield over motor housing as shown.
Fig. 2-2
3. Align edging guide with mating grooves and push firmly in the direction shown until an audible
snap is heard.
NOTE: Be certain that edging guide is oriented as shown. Once edging guide, motor housing and
debris shield are mated the connection is permanent and cannot be removed without a special tool.
EXCHANGE OF SPOOL
Turn off the machine and disconnect the plug from power supply. Wait until nylonline has come to a
complete stop. Pict. 2-3 Press both press-buttons 1 and lift off the cover 2. Pict. 2-4 Replace the empty
spool 3 by inserting each line end through the eyelets as shown. Secure the spool with a slight turn to
ensure correct position in the base plate. Then replace the cover ensuring both press-buttons lock in.
NOTE: The complete spool and line must be replaced and line must be replaced and is available as
an accessory.
c
PRODUCT ADJUSTMENTS
Fig. 3-1 - Adjustment Assist Handle
1. Using thumb and forefinger push in both spring loaded lock buttons at the base of the assist
handle in order to release the ratchet adjustment mechanism.
2. Adjust handle as necessary and release automatic lock buttons.
Fig. 3-2 - Adjust Shaft Length
1. Grip shaft firmly.
2. Push red shaft release button forward and move handle forward or backward to desired length.
NOTE: Shaft may be adjusted in trimming or edging mode.
Fig. 3-3 - Edging Conversion
1. Grip shaft firmly.
2. Push red button forward and rotate handle assembly until an audible click is heard.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Flymo Power Trim - 2001 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Flymo Power Trim - 2001 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info