631059
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
2. Charging the battery and
placement of the boundary wire
See chapter 3.3 and 3.4 in the Installation Manual
1. Place the robotic lawnmower in the charging station
to charge the battery while the boundary wire is laid.
Set the main switch to position 1.
2. Run the boundary wire ensuring it forms a loop
around the work area.
3. Make an eyelet at the point where the guide wire
will be connected later (see point 4.5).
20 cm / 8”
10 cm / 8”
0 cm / 0”
5 cm / 2”
30 cm / 12”
1. Placement of and connecting the
charging station
See chapter 3.2 in the Installation Manual
1. Place the charging station at a central position in the work area, with
a lot of open space in front of the charging station and on a relatively
horizontal surface.
2. Connect the transformers low voltage cable to the charging station
and the transformer.
3. Connect the transformer to a 230 V wall socket.
1. Main switch
2. STOP button
3. LED for function check of the
boundary and guide wires
4. Cutting height indication
5. Display
6. Keypad
Charging station
12345
1 2 3
4 5 6
7 8
0
9
Start
4
5
6
1
2
3
GETTING STARTED WITH THE FLYMO
1
1
2
3
7
4
min 2 m / 7 ft
1
1
4. Placement of and connecting the
guide wire
See chapter 3.6 in the Installation Manual
1. Run the guide wire through the slot at the bottom of the charging
station.
2. Fit the connector to the guide wire in the same way as for the
boundary wire, according to the instructions above.
3. Fasten the connector to the contact pin marked Guide on the
charging station.
4. Lay the guide wire at least 2 metres straight out from the front edge
of the charging station.
5. Run the guide wire to the point on the boundary loop the connection
will be made. Avoid laying the wire at tight angles.
6. Cut the boundary wire with a wire cutters at the centre of the eyelet
that was made in point 2.3.
7. Connect the guide wire to the boundary wire using the
accompanying couplers. Press the couplers completely together
with a pair of pliers.
1 2
4
3
3. Connecting the boundary wire
See chapter 3.5 in the Installation Manual
1. Open the connector and lay the wire ends in the recesses on
each connector.
2. Press the connectors together using a pair of pliers.
3. Cut off any surplus boundary wire. Cut 1 to 2 cm above
the connectors.
4. Press the connectors onto the contact pins, marked A, on
the charging station. It is important that the right-hand wire
is connected to the right-hand contact pin, and the left-hand
wire to the left-hand pin.
Transformer Low voltage cable Boundary wire
and couplers
Pegs Connectors Measurement
gauge
1200 R ROBOTIC LAWNMOWER
5cm
0cm
20cm
30cm
30 cm / 12”
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Flymo 1200R - 2013 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Flymo 1200R - 2013 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Flymo 1200R - 2013

Flymo 1200R - 2013 Installatiehandleiding - English - 70 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info