763957
48
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
287/289
Users Manual
38
Measuring Current
XW Warning
To avoid damage to the Meter and possible injury,
never attempt an in-circuit current measurement
where the open-circuit potential to earth is greater
than 1000 V.
W Caution
To avoid possible damage to the Meter or to the
equipment under test, check the meter’s fuses
before measuring current. See the Maintenance
section later in this manual. Use the proper
terminals, function, and range for your
measurement. Never place the probes across (in
parallel with) any circuit or component when the
leads are plugged into the current terminals.
Current is the flow of electrons through a conductor. To measure
current, you must open the circuit under test, then place the
meter in series with the circuit.
Note
When measuring current, the display will flash when
the input current exceeds 10 amps for the A terminal
and 400 mA for the mA/
μ
A terminal. This is a warning
that current is approaching the fuse’s current limit.
To measure ac or dc current, proceed as follows:
1. Turn off power to the circuit. Discharge all high- voltage
capacitors.
2. Insert the black lead into the COM terminal. Insert the red
lead in an input appropriate for the measurement range.
Note
To avoid blowing the Meter’s 440 mA fuse, use the
mA/
μ
A terminal only if you are sure the current is less
than 400 mA.
3. If you are using the A terminal, set the rotary switch to A.
If you are using the mA/μA terminal, set the rotary switch to
X for currents below 5000 μA (5 mA), or A for
currents above 5000 μA. See Figure 21 for test lead
connections and function selection. Refer to the “Input Alert
Feature” section for information on the alerts the Meter uses
when leads are not used correctly for current
measurements.
4. As shown in Figure 22, open the circuit path to be tested.
Touch the red probe to the more positive side of the break;
touch the black probe to the more negative side of the
break. Reversing the leads will produce a negative reading,
but will not damage the meter.
5. Turn on power to the circuit; then read the display. Be sure
to note the measurement unit given at the right side of the
display (μA, mA, or A).
6. Turn off power to the circuit and discharge all high-voltage
capacitors. Remove the Meter and restore the circuit to
normal operation.
48

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 289 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 289 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Fluke 289

Fluke 289 Gebruiksaanwijzing - Nederlands - 90 pagina's

Fluke 289 Gebruiksaanwijzing - Deutsch - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info