576716
53
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
48
FBS 43 B2
GB
The air fi lter must be checked more frequently if the air is dusty.
1.) Remove the air fi lter housing cover
(see fi g. 10a).
2.) Remove the air fi lter
(see fi g. 10b + 10c).
3.) Clean the air fi lter
by tapping or blowing it out (with compressed air).
4.) Assembly takes place in reverse order.
IMPORTANT!
Never clean the air fi lter with petrol or fl ammable solvents.
Spark plug maintenance
1.) Remove the spark plug connector
(see fi g. 11a).
2.) Remove the spark plug using the enclosed spark plug spanner
.
3.) Assembly takes place in reverse order.
Electrode gap = 0.6 mm (distance between the electrodes between which
the ignition spark is generated). Tighten the spark plug with 12 to 15 Nm
of torque using a torque wrench (available from specialist retailers).
Initially check the spark plug for contamination after 10 hours of operation
and clean this with a copper wire brush if required.
Then service the spark plug after every 50 hours of operation.
Grinding the protective hood blade
The protective hood blade
(see fi g. 7a) may become blunt over time.
If you notice that this is the case, loosen the 2 screws used to fasten the
protective hood blade
to the cutting line protective hood . Clamp
the blade in a vice. Grind the blade with a grindstone and ensure that the
correct angle of the blade edge is maintained. Only grind in one direction.
Adjusting the carburettor
The air fi lter housing cover
must fi rst be removed, as displayed in fi g.
10a, before performing any work on the carburettor.
Adjusting the throttle cable
If the device's maximum speed is no longer reached over time and all other
causes in accordance with the "Troubleshooting" section have been ruled
out, this may mean that the throttle cable needs to be adjusted.
NOTE
First check whether the carburettor opens completely when the throttle
lever is fully engaged.
This is the case if the carburettor slide (see fi g. 13b) is completely open at
full throttle. Figure 13a shows the correct setting. An adjustment is necessary
if the carburettor slide is not fully open.
The following steps must be taken to adjust the throttle cable:
Loosen the locking nut (see fi g. 13a) a few turns. Unscrew the ad-
justing screw (see fi g. 13a) until the carburettor slide is completely
open at full throttle (see fi g. 13b).
Retighten the locking nut .
Adjusting the idling rate
IMPORTANT!
Adjust the idling rate once the device has warmed up.
If the device does not come to a stop when the throttle is not engaged
and all other causes in accordance with the "Troubleshooting" section
have been excluded, it may mean that a readjustment of the idling rate is
required. Rotate the idling screw
(see fi g. 5a) in a clockwise direction
until the device idles smoothly. If the idling rate is so high that the cutting
tool rotates, this must be reduced by turning the idling screw to the left until
the cutting tool no longer rotates.
Lubricating the gears
Add gear grease after every 20 hours of operation (approx. 10 g).
To do so, open the screw (see fi g. 7c).
Spare part orders
Ordering spare parts
The following information must be provided when ordering spare parts:
Type of device
Item number of the device
Device ID number
Current price and information is available at
www.kompernass.com
Storage and transportation
Store the device in a safe location.
Store the device and accessories in a safe location that is protected
against naked fl ames and sources of heat/sparks, such as gas-powered
water heaters, dryers, oil stoves or mobile heaters, etc.
Always keep the cutting blade protective hood , the line spool
and the engine free of mowing residue during storage.
Always turn the device off before performing any maintenance work
and remove the spark plug connector .
Storing the device
The device must be prepared for storage if it is to be stored for longer than
30 days. Otherwise the residual fuel in the carburettor will evaporate and
leave a rubbery sediment. This may make starting the device more diffi cult
and result in expensive repair work.
1.) Remove the fi ller cap in order to relieve any pressure in the fuel tank
.
Carefully empty the fuel tank
.
2.) Start the engine and leave it to run until it stops in order to remove all
fuel from the carburettor.
3.) Allow the engine to cool for about 10 minutes.
4.) Remove the spark plug (see "Spark plug maintenance" chapter).
5.) Add 1 teaspoon of 2-stroke oil to the combustion chamber. Pull the
starter pull cord
several times in order to wet all mechanical parts
with oil. Re-insert the spark plug.
NOTE
Store the device in a dry place and away from possible ignition
sources.
IB_97786_FBS43B2_LB1.indb 48 03.07.14 15:16
53

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Florabest-FBS-43-B2---IAN-97786

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Florabest FBS 43 B2 - IAN 97786 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Florabest FBS 43 B2 - IAN 97786 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 1,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info