714372
4
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers
Rear Wheel Assembly
1. Assemble the rear wheel bolt (A) through the rear wheel washer
(B) and insert through the rear wheel (C).
2. Screw the bolt assembly into the swing arm (D) and tighten firmly
using the 18 mm wrench or socket.
3. Repeat for the other rear wheel.
Attaching the Handle
1. Remove the two cotter pins (A) from the handle mount pegs (B).
2. Slide hole number 2 (C) of the handle onto the handle mount pegs (B).
Some force may be needed to separate the handle legs so they fit over
the pegs. Release the handle until it rests on the handle stop peg (D).
3. Insert the cotter pins (A) to secure the handle.
Assembly
Assembly
A
B
C
D
A
B
C
D
6 7
4. Slide handle shroud (E) into place from below with the Fiskars logo facing
down and toward the upper handle section (B).
5. Align holes in handle sections and shroud (E). Slide a handle bolt (F) through
from the inside, so that the end comes through the hole of the handle shroud.
Repeat for the remaining three handle bolts.
6. Align the hex-shaped bolt head with the hex-shaped cutout in the center
handle section (A), then hand-tighten a handle nut (G) onto the bolt.
Repeat for the remaining three handle nuts.
7. Using an 11 mm wrench or socket, tighten the four handle nuts (G) until
they are snug.
Handle Assembly
1. Lay out the handle parts upside down as shown above for easier
assembly. Note the center handle section (A) is symmetrical, so it can
be laid down on either side.
2. Make sure the arch of the upper handle section (B) is facing down.
Then insert the free ends of the upper handle section (B) into the center
handle section (A). Roughly align the holes.
3. Make sure the lower handle sections, (C) and (D), are laid out with the
notches up. Then insert the left lower handle section (marked with “L”) (C)
and the right lower handle section (marked with “R”) (D) into the center
handle section (A) as shown. Roughly align the holes.
The following parts are included in the hardware bag (bagged separately):
Handle Assembly
Handle nuts (4)
Handle bolts (4)
B
A
C
D
1
2
3
Rear Wheel Assembly (next page)
Rear wheels (2)
Rear wheel bolts (2)
Rear wheel washers (2)
Tools required for assembly:
The only tools required for assembly are
11 mm and 18 mm wrenches or sockets.
L
R
A
B
C
D
E
(left)
(right)
F
G
Handle Arch
(pointed down)
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fiskars Stay Sharp - 6208 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fiskars Stay Sharp - 6208 in de taal/talen: Engels als bijlage per email.

De handleiding is 15,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info