795138
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
56
Test Locking System Programming A Personal Passcode
TESTING THE PASSCODE
1 With the safe door open and the Live Bolts engaged, you can now
test the Electronic Locking System using the pre-set three digit
factory code. Locate the digital keypad on the front of the safe
and open up the protective cover to expose the keypad.
2 When the cover is opened, the keypad is activated and the
keypad backlight will turn on and remain on for approximately
ve (5) seconds. The keypad is still active even when the
backlight turns o. It will turn on again when any key is pressed.
3 The pre-set three digit factory passcode is 159. Enter this
passcode as follows:
*51 9 #
Note: All eNtries Are AccompANied by A beep ANd
the greeN light will flAsh.
4 After properly entering the entire sequence, the green light will turn on and the
lock will click. You now have ve (5) seconds to open the safe by turning the safe
door handle upward to the right.
ImPortAnt IF HANDLE WILL NOT TURN
If the handle will not turn to the right after the green light
comes on, rst turn the handle slightly back to the left until it
stops, then turn upwards to the right again to open.
5 Once the handle has been turned to the right, the live
bolts will disengage and retract into the door. At this point
you have successfully unlocked the safe and the door
can be opened. Note: This waterproof safe may require
additional force upon initial entry.
6 Leave the safe door open and proceed to Programming
a Personal Passcode.
ImPortAnt SECURITY LOCKOUT PERIODS
For added security, the safe will automatically lock out
entry for 15 minutes after three (3) attempts to open with
an invalid passcode.
ProgrAmmIng A PerSonAl PASScode
For security reasons, it is very important that
you program your own personal passcode
into the digital lock. The factory code should
be changed immediately.
To program your own unique three to eight
digit (3-8) passcode, follow these steps:
Note: After pressiNg the reset buttoN, the red ANd greeN lights
oN the keypAd will flAsh to iNdicAte the progrAmmiNg
is Authorized ANd you hAve 10 secoNds to begiN.
1 Open the protective cover on the front of the safe to expose the keypad.
2 With the safe in the open position, press the small reset button located on
the inside top edge of the door.
3 Enter your new three to eight digit (3-8) passcode followed by the # key.
OS CA S
PED #
Immediately repeat the sequence, beginning with the new passcode
followed by the # key.
OS CA S
PED #
4 The green light will light up solid for 5 seconds, indicating your new passcode
has been successfully entered.
5 Your new passcode will now be comprised of the three to eight (3-8) digit
sequence you selected, always followed by the # sign. The factory pre-set
Passcode will no longer open the safe.
6 You may change your passcode at any time by repeating the
same steps.
7 It is important that you write down your personal passcode
and secure it in a safe location away from the safe.
1
4
7
2
5
8
0
3
6
9
#
15
mInuteS
!
Minimum 3 Digits
1
4
7
2
5
8
0
3
6
9
#
Reset Button
ImPortAnt ONCE YOUR PERSONAL PASSCODE IS PROGRAMMED, THE
FACTORY PRESET CODE WILL NO LONGER OPEN THE SAFE.
Note: if you forget your persoNAl pAsscode, Access to the
sAfe cAN be mAde usiNg the emergeNcy override key.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw First Alert 2096DF-BD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van First Alert 2096DF-BD in de taal/talen: Engels als bijlage per email.

De handleiding is 6.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info