574925
11
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
11
a danger of rupturing concealed gas/water
pipes or cutting through power cables.
- Do not open the battery pack or the charger.
Even after disconnection from the mains,
there is still a high capacitor voltage inside
the charger.
- Make sure that metal objects (such as metal
chips) do not collect in the battery pack retai-
ning slots or enter the machine through the
air vent slits (danger of short circuit).
- Protect the battery pack from excessive heat
or constant heat sources such as sunlight or
naked ames. There is a risk of explosion.
1.3 Noise and vibration information
Cordless drill/screwdriver
The typical values determined in accordance
with EN 60745 are:
Sound pressure level 72 dB(A)
Sound-power level 83 dB(A)
Measuring uncertainty allowance K = 4 dB
The noise level can exceed 85 dB(A)
during operation.
Wear ear protection!
Vibration emission value a
h
(vector sum for
three directions) and uncertainty K measured
in accordance with EN 60745:
Drilling in metal a
h
< 2,5 m/s²
K = 1,5 m/s²
Screws a
h
< 2,5 m/s²
K = 1,5 m/s²
1.4 Wall mounting LC 45
The charger LC 45 has two longitudinal slots on
its rear by which it can be suspended on walls
using two screws (e.g. button-headed or at
head screw with a shaft diameter of 5 mm).
Screw both screws into the wall 96 mm apart
until the screwhead is protruding from the wall
by approx. 4 mm.
2 Machine settings
Remove the battery pack before any adjust-
ments, maintenance or repair is carried out!
2.1 Exchanging the battery pack
Removing battery pack
Press the two buttons (1.1) and slide the bat-
tery pack forwards to remove.
Inserting battery pack
Slide the battery pack into the holder on the
underside of the handle until it latches into
place (see Fig. 1).
2.2 To change the direction of rotati-
on
The selector button (1.4) determines the direc-
tion of rotation. Turn button from right to left =
clockwise rotation. Turn button from left to
right = anticlockwise rotation. Selector but-
ton in central position = circuit interlock.
2.3 Shifting speeds
Change only when completely stop-
ped!
Using the shift lever (1.5), the speed can be
changed.
1. Speed: Lever forward - Figure 1 is visible.
2. Speed: Lever backwards - Figure 2 is vi-
sible.
2.4 Torque adjustment
By turning the adjustment ring (1.6) the re-
quired torque can be adjusted. The arrow (1.7)
aligns with the adjusted state.
Drilling
Drilling symbol on adjustment ring aligns with
the arrow = maximum torque.
Screws
Torque corresponding to setting:
Position 1 = low torque
Position 20 = high torque
3 Tool holding xture, attachments
3.1 Chuck BF-FX
The chuck is used to clamp drills and bits.
a) Fitting/removing the chuck
Fitting
- Place the chuck on the drill spindle (2.5) and
twist until the hexagon key (2.4) of the chuck
latches into the hexagon socket of the drill
spindle.
- Pull the unlocking ring (2.3) forwards, press
the chuck onto the drill spindle up to the stop
and release the unlocking ring.
Removal
- Pull the unlocking ring forwards and remove
the chuck.
b) Changing tools
- Turn the clamping sleeve (2.2) anti-clockwise
to open the clamping jaws (2.1) (Note: the
spindle is automatically locked when the ma-
chine is switched off).
- Insert the tool into the chuck.
- Clamp the tool by turning the clamping sleeve
clockwise. Always make sure that the tool is
clamped centrally in the chuck.
3.2 Angle attachment DD-AS
The angle attachment permits work (drilling,
screwing) vertical to the machine’s longitudinal
axis.
a) Fitting/removing the angle attach-
ment
Fitting
- Place the angle attachment on the drill spindle
and turn until it catches in the desired position
(Note: The angle attachment can be tted in
16 different angle settings).
- Lock the angle attachment by turning the
fastening ring (2.7) tightly clockwise.
Removal
- Turn the fastening ring anti-clockwise up to
the stop and remove the angel attachment.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TDK 15.6-15.6 V Li bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TDK 15.6-15.6 V Li in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info