778612
25
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
25
P R E C I S I O - GB
- Clean any contamination, grease, oil and water
off the clamping surfaces.
- Clamping screws must be tightened according
to the manufacturer's instructions.
- Do not lengthen the key or tighten by hitting with
a hammer.
- The tools must be stored and transported in a
suitable container.
- Only use the machine if all safety devices are in
their correct positions, the machine is in good
condition and has been well maintained.
- Replace worn or damaged (e.g. by saw blade
cuts) plates without delay.
- Operating personnel must have received ade-
quate training in the use, set-up and operation
of the machine.
- Faults on the machine, including the separating
guards or the tool, must be reported to main-
tenance staff immediately upon discovery. The
machine must not be used until the fault has
been eliminated.
- Wear suitable personal protec-
tive equipment:
Ear protection to reduce the risk
of hearing loss, safety goggles,
a dust mask to prevent inhala-
tion of harmful dust, protective
gloves when working with raw materials and
when handling tools.
- To minimise noise, the tool must be sharpened
and all noise-reducing elements (covers, etc.)
must be properly adjusted.
- When cutting wood, connect the machine to a
dust extractor corresponding to EN 60335-2-69,
dust class M.
- To minimise the release of dust, the machine
should be connected to a suitable dust extractor.
All dust extraction elements (dust extraction
attachments, etc.) must be properly adjusted.
- Never process material that contains asbestos.
- Make sure that you have enough light in the
room or work place.
- When sawing, adopt the correct working posi-
tion:
- At the front on the side of the operator;
- Head-on to the saw;
- Beside the line of cut.
- Use the accompanying push stick to guide the
workpiece accurately past the saw blade.
- Always use the supplied riving knife and the
guard. Ensure that they are set correctly as
described in the operating instructions. If the
riving knife is set incorrectly and components
that are required for safety reasons (such as the
guards) are removed, this may result in serious
injuries.
- Use a suitable device to support long workpieces
and ensure that they are horizontal.
- Pull the plug from the mains power socket be-
fore changing tools and rectifying faults such as
removing trapped splinters.
- Do not remove offcuts or other workpiece parts
from the cutting area while the machine is still
running or before the saw blade stops moving.
- If the saw blade jams, switch the machine off
immediately and disconnect the mains plug. Do
not remove the jammed workpiece until you have
done this.
- Cutting rebates or grooves is only permitted
when a suitable protective device has been fitted,
e.g. a protective tunnel over the saw table.
- Reinstall the safety equipment immediately af-
ter work that requires the guard to be removed,
see section 6.2b.
- Do not use circular saws for cutting slots
(grooves in workpiece).
- Before transporting the machine, make sure
that the top guard covers the top section of the
saw blade.
- Do not use the top guard as a handle for trans-
portation.
- When not in use, store the push stick in the
accessory holder provided on the machine.
- Use only original Festool accessories and aids.
- Use of your own aids e.g. push stick, rulers, etc.
is not permitted.
- Before commencing work, check that the guard
and splinter guard can move freely and are rest-
ing on the table.
- To prevent the saw blade from overheating or
the plastic from melting, set the correct speed
for the cutting material and do not use excess
pressure when cutting.
- When cutting metal, switch on the saw using a
residual current circuit breaker.
- Check the plug and the cable regularly and
should either become damaged, have them
replaced by an authorised after-sales service
workshop.
- Only for AS/NZS: The tool shall always be sup-
plied via residual current device with a rated
residual current of 30 mA or less.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool PRECISIO CS 70 EG - 2020 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool PRECISIO CS 70 EG - 2020 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info