778817
24
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
22
KA 65
GB
11
Troubleshooting
Problem Possible causes Remedy
Machine stops operating. Flap
[1-18]
is open.
The supply of adhesive stops
if the flap is opened during
operation. However, the feed
mechanism continues to
operate.
Close the flap
[1-18]
.
Error message (appears on
the display
[1-20]
): edge
band not yet inserted.
Remove the edge band.
The machine switches off. The machine is in cooling
mode < 50 °C Press the start button
[1-1]
to switch on
the machine again.
Display lights up red. The machine switches to
cooling mode after an idling
time of 15 minutes.
Press the start button
[1-1]
to switch on
the machine again.
Inlet switches off before the
edge band is inserted. The time window of 20 sec-
onds has been exceeded. Press the start button
[1-1]
to start the
drive again.
Inlet does not switch off even
though the edge band has
passed through the machine.
Light barrier
[3-4]
is dirty. Clean the light barrier
[3-4]
carefully.
The display shows the prompt
to remove the edging
although no edging is
inserted.
Edge band does not adhere. Surface dirt/nozzle holes are
blocked. Initiate the purging process to remove any
dirt
(chapter 8.3)
.
If the contamination is more severe, raise
the central plate completely and pierce
the lower nozzle holes during operation.
Adhesive too runny/too firm,
too much/too little Incorrect temperature,
incorrect amount of adhe-
sive set.
Adjust temperature to adhesive cartridges
used
using the menu keys
[1-19]
.
Adhesive too runny: Temperature -10 °C
Adhesive too firm: Temperature +10 °C
If required, adjust amount of adhesive with
[1-19]
.
Insufficient adhesive applied
to thin edge bands (approx.
0.5 - 0.8 mm depending on
material) at the start of glue-
ing
Lack of edge band pressure
on the adhesive nozzle. At the start of gluing, place an additional
piece of edge band (approx. 20 cm) with
the same edge height behind the main
edge band. This additional piece is guided
into the edge inlet after the edge band.
Error symbol appears on the
display
[1-20]
.The machine electronics
have detected a serious
error.
Switch off the machine by pressing the on/
off switch
[1-8]
and allow to cool for a few
minutes.
Switch on the machine again by pressing
the on/off switch
[1-8]
.
If the error symbol appears again, contact
after-sales service.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool KA 65 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool KA 65 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 26,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info