499178
15
Verklein
Vergroot
Pagina terug
1/110
Pagina verder
CTM 48 E LE EC/B22, CTL 48 E LE EC/B22
15
GB
aged. Always replace the mains power
cable with the type specified in the spare
parts list.
– Do not expose the machine to rain.
For reasons of safety, never operate the
machine from an unearthed socket.
Always use the machine socket for the pur-
pose specified in the manual.
– Always use original Festool accessories.
Pull the plug from the socket when the ma-
chine is not in use and prior to mainte-
nance and cleaning work.
Design 22 dust extractors are suitable for
connecting to machines in Zone 22. Care
must be taken to ensure that no sources of
ignition are extracted. Conductive machine
components, including extractor hoods,
and conductive parts on machines from
protection class II must be electrostatically
earthed. The electrostatic earthing can be
routed through the dust extractor or estab-
lished using separate electrostatic earthing
equipment.
– Do not lift or transport the machine by the
handle using a crane or lifting gear.
The device may only be operated if all fil-
ters are present and undamaged, including
the filter for the motor cooling air.
Do not insert and remove the plug under
load.
In an emergency (e.g. short circuit or other
electrical faults occur), switch off the ma-
chine and pull out the mains plug.
6 Operation
6.1 Initial operation
X
Open the locking clips [2-2] and remove
the top section of the machine[2-1].
X
Remove the accessories from the dust
container [2-3] and the packaging!
X
Insert a filter bag in the dust container
that fulfils statutory requirements (see
chapter 7.8).
X
Replace the top section [2-1] and close
the locking clips [2-2].
X
Attach the cable holder to the rear of the
mobile dust extractor (see Fig. [3]).
X
Insert the sealing plug [1-1] on the panel
(see Fig. [1] ).
X
Connect the suction hose to the machine.
6.2 Switch on/off
X
Insert the plug into an earthed socket.
The use of extension cables in Zone 22
is not permitted.
The switch [1-9] serves as an on/off switch.
Switch position "0"
Appliance socket [1-11] is disconnected from
the power, mobile dust extractor is switched
off.
"MAN" switch position
Appliance socket [1-11] is connected to the
power, the mobile dust extractor starts.
"Auto" switch position
Appliance socket [1-11] is connected to the
power, the mobile dust extractor starts when
the connected tool is switched on.
7 Settings
7.1 Adjusting the hose diameter
X
Adjust the hose diameter adjuster [1-8]
to match the diameter of the connected
hose.
L
The monitoring devices will measure the
air speed in the extractor hose correctly
as a result (see chapter 7.9).
WARNING
Unauthorised voltage or frequency!
Risk of accident
X
The mains voltage and the frequency of
the power source must correspond with
the specifications on the machine's name
plate.
X
In North America, only Festool machines
with the voltage specifications 120 V/60
Hz may be used.
CAUTION
Risk of injury from tools starting up un-
expectedly
X
Before setting the switch to the "AUTO" or
"MAN" position, make sure that the con-
nected tool is switched off.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool CTM B22 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool CTM B22 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info