510129
5
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
5
EN
8. Motor
9. Mains cable
10. Frame
11. Rip fence
12. Interlocking knob
13. Mitre guide
14. Nut
15. Screw
2. SAFETY INSTRUCTIONS
Explanation of symbols
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-obser-
vance of the instructions in this manual.
Indicates the presence of an electrical
voltage.
Keep bystanders away.
Wear eye and ear protection.
Wear a dust mask protection.
Wear gloves when handling saw blades
and rough materials. Saw blades shall be
carried in a holder whenever practicable.
Before using the appliance
Make sure that the saw bench is adequately
and effectively illuminated.
When you use strip lighting you should be
aware of the so-called stroboscopic effect.
This may cause a rotating saw blade to appear
to be stationary. One solution is to use two
fittings in order to create
phase displacement.
Check the following points:
Does the voltage of the motor and any fuse
employed correspond with the mains voltage?
Appliances with a voltage of 230 V~ may
be connected without problems to a mains
voltage of 220 V~.
Are the feeder cable and plug in good condition:
sturdy, without loose bits or damage?
Has the saw blade lost any teeth or is it
displaying cracks or fractures? If so, replace
the saw blade immediately.
The protective hood may not be set higher
than required to let the workpiece pass.
The riving knife should be narrower than the
saw cut and broader than the saw blade.
Do not exercise lateral pressure on the saw
blade as it may cause it to break.
Check the wood for knots, nails, cracks and
waste residues.
These irregularities may cause the workpiece
to kick back dangerously.
Ensure that no objects get into the extraction
system.
These objects may come into contact with the
saw blades resulting in potentially hazardous
situations.
Replace table insert when worn.
Rebating or grooving should not be carried out.
Saws shall not be used for slotting (stopped
groove).
Use only saw blades for which the maximum
possible speed is not less than the maximum
spindle speed of the tool and the material to be
cut.
When transporting the machine use only
transportation devices and do never use
guards for handling or transportation.
During transportation the upper part of the saw
blade should be covered by the guard.
Using the appliance
Push the workpiece that you are going to saw
securely to the table surface.
Hold at the same time the section of the
workpiece that has been sawed to prevent it
breaking off. The hand that secures the sawed
section should remain behind the saw blade and
move away from it. Make sure that the hand that
you use to secure the workpiece does not cross
the hand that you use to operate the appliance.
Use the push stick supplied with the appliance.
Use the push stick to guide smaller
workpieces past the saw blade.
Do not use long extension cables.
Allow the appliance to cool off before moving it.
Do not remove wood residues in the vicinity of
the saw by hand.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TSM1032 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TSM1032 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 6,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ferm TSM1032

Ferm TSM1032 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Espanõl - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info