58 Ferm
SPARE PARTS LIST FZT-250E
FERM NR DESCRIPTION REF NR
407870 GUARD COMPLETE 001 T/M 004
407871 RIVING KNIFE 005
407872 ANGLE GUIDE COMPLETE 006+007+008+013
407873 GUIDE FOR ANGLE GUIDE 009+010+011+012
407874 INLAY 016
407875 WORKBLADE RIGHT 017
407876 WORKBLADE LEFT 018
407877 GUIDE FOR FENCE 019+020+022+029
407878 SUPPORTING ARM SHORT 023
407880 FENCE 030+031(2X)
407881 HOLDER FOR FENCE 032 T/M 036+012
806003 BALL BEARING 6003 ZZ 044
407464 GEAR SHAFT 045
407465 KEY 046
407466 GEAR 047
407467 ROTOR 053
407468 STATOR 055
806001 BALL BEARING 6001 ZZ 056
407485 MOTOR HOUSING 057
407492 CARBON BRUSH HOLDER 058 + 060
407469 CARBON BRUSH SET 059
407472 HEX.NUT M16X1.5 079
407470 FLANGE OUTSIDE 080
310360 TCT SAWBLADE 250 MM 081
407471 FLANGE INSIDE 082
407473 CRANK 091
407475 FIXED BRACKET 110 + 111
407496 SWITCH 120
407883 WORKBLADE REAR 123
407879 SUPPORTING ARM LONG 124
407882 HOLDER FOR PUSH STICK 130
407498 MOTOR _
407497 THERMICAL SWITCH _
407884 FLOORSTAND COMPLETE _
407885 RUBBER FOOT FOR FLOORSTAND _
407886 COMPLETE SET SCREWS FOR FLOORSTAND _
SAW BENCH
THE NUMBERS IN THE FOLLOWING TEXT
CORRESPOND WITH THE PICTURES AT PAGE 2.
TECHNICAL SPECIFICATIONS
PRODUCT INFORMATION
Fig. A
1 Protective cap
2 Fence
3 Bench inlay
4 Mitre handle
5 Height handle
6 Measurement set-up for fence
7 On/off switch
8 Bench protractor for mitring
9 Workbench
Check first whether or not the delivery has been damaged
by transport and/or whether all the parts are present.
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to reduce
the risk of fire, electric shock and personal injury. Read
the following safety instructions and also the enclosed
safety instructions.
Always check that the power supply corresponds to
the voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
• As a supply for this machine always use an unloaded
line and/or an extension cable with conductors of at
least 1,5 mm
2
and protected with a 16 A fuse. Be sure
that this extension cable is not longer than 20 metres.
• Only connect your machine and/or extension cable
to an earthed electricity mains.
• This machine can be switched to the single-phase
network (230 V/50 Hz). If you are in doubt about the
earth of the electricity provisions, consult an
electrician first.
BEFORE USE, REMOVE THE TRANSPORT
PROTECTION:
• Disassemble the bottom plate by loosening the 4
screws.
• Remove the transport protection below motor.
• The handles for height and mitre setting of the saw
blade are
located in the transport protection inside the
machine.
• Reassemble the bottom plate.
ADDITIONAL SAFETY INSTRUCTIONS
1 When using the saw blades with hard metal teeth
(Carbon tipped) it is advisable to use blades with a
negative or slightly positive cutting angle. Do not use
any saw blades with deeply cut teeth. They can grip
the protective cap.
Voltage | 230 V~
Frequency | 50 Hz
Power input | 1500 W
No load speed | 4500/min
Saw blade dimensions | 254x15.9
| x3.2mm
Number of teeths | Z40
Measurements of bench | 638x430 mm
Dust extraction outlet | 30(20) mm
Weight | 37.9 kg
Lpa (sound pressure level) | 99.3 dB(A)
Lwa (sound power level) | 112.3 dB(A)
Ferm 3
