510126
5
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
EN
5
Ferm
and the plate.
• Mounting the saw blade.
• Unscrew two screws out of lower blade guard
and remove the guard.
• Dismount nut (counterclockwise) and outer
flange .
• Place blade on the inner flange.
• Mount outer flange and nut (clockwise) again.
• Place the lower blade guard back in position
and connect the two screws.
• Mounting the upper blade guard (11).
• Slide the guard in horizontal position across
the riving knife.
• Connect the guard to the riving knife with the
bolt (12) and the locknut.
• Be aware that the guard is connected under
the lock-pin (13). The lock-pin prevents the
guard falling backwards.
• Mounting the adjustable fence
• Connect the knob (7) with the fence (3) by
using the plate (1 hole with thread); do not
tighten the knob yet.
• Slide the complete fence with (loosen) knobs
onto the table; the plates on the inner side of
the table.
• Set the required distance.
• Tighten the knobs by rotating them
(clockwise).
• Place the water tank (4) under the table.
Installing the tile cutter
• The tile cutter may only be used as a fixed tool
and should be screwed down to a level and
horizontal surface. Please use the screw holes
in the base of the machine.
• The electrical supply must be connected to a
230 V earthed wall socket. The mains voltage
must comply with the information on the type
plate, and must be protected by a circuit
breaker.
• Do not use the power cable to pull the plug
from the socket. Protect the cable against
heat, oil and sharp objects.
Only use accessories and auxiliary
equipment mentioned in the instructions
for use or recommended or mentioned by
the manufacturer. Using other
accessories or auxiliary equipment may
carry a risk of injury for you and others.
4. Operation
Operation
Fig.1
• Before starting the job, please ensure there is
sufficient water in the water tray (4) i.e. the
diamond blade runs through the water. During
the job, the water tray must be topped up.
• Do not start working before the maximum
speed has been reached.
• The diamond blade must NEVER be exposed
to sideways pressure; they can break and the
flying pieces become projectiles!
• Do not attempt to cut extremely small pieces
from the tiles. Always make sure that the full
surface of the tile is on the work table. The
supplied mitre guide can be used to push the
tiles through the cutter. In the early stages of
cutting in particular, the tile must remain
absolutely level to avoid the tile moving up.
• Do not overload your tool. It is better and safer
to work within the indicated power range. Do
not cut materials other than tiles.
• Maintain your tools carefully. Keep the tools
sharp and clean in order to work properly and
safely.
• Follow the maintenance instructions and the
instructions for replacing the diamond blade.
• Stand safely and maintain your balance. Avoid
any unnatural body angles. Remain alert and
pay attention to your work. Use common
sense. Do not use the machine when you
cannot concentrate or when you are tired.
Full-length adjustable fence
Fig.1
The fence (3) enables you to cut parallel to the
cutting blade. Set up: Loosen the knobs (7) and
set the required distance. Tighten the knobs on
both sides of the work table. The markers
determine the measurements (8).
Mitre guide
Fig.1
The mitre guide has a variable setting between 0°
and 45°. Loosen the knobs (5), set the mitre by
tilting the table (1) up until you have reached the
required tilt. Tighten the knobs (5) again on both
sides of the work table.
Checking and replacing the diamond blade
Fig.1 + 2
• Cracked or distorted diamond blades must be
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TCM1011 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TCM1011 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ferm TCM1011

Ferm TCM1011 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Espanõl - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info