510102
3
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
EN
3
Ferm
MULTIPURPOSE GAS SOLDERING
TOOL
The numbers in the following text correspond
with the pictures at page 2
Features
1. Switch
2. Shut off lever
3. Nut
4. Soldering head
5. Filling valve
6. Flow control knob
7. Ignition button
8. Guard
9. Standard tip
10. Diagonal tip (3 mm)
11. Chisel tip (3,5 mm)
12. Hot knife
13. Hot blower
14. Reflector
15. Wrench (7 mm)
16. Wrench (8 mm)
Warnings
• Donotfillgasorstorenearopenflame,heater
or combustible materials
• Useonlyhighqualitybutanegas
• Butanegasishighlyflammable,pleasehandle
with care
• Donotdrop,puncture,orincinerate
• Donotstoreoroperateinaplacewherethe
temperature is above 50º C (122º F)
• Keepoutofreachofchildren
• Cooldownbeforeputtingprotectivecapon
and before storing
Gas filling and refilling
• Ensuretheswitch(1)isturnedtotheOFF
position before filling
• Reversetheunit;insertthegascontainer’s
nozzleverticallyintofillingvalve(5)
• Whengasescapesfromfillingvalve,remove
the nozzle from the filling valve
Ignition
• Movetheflowcontrolknob(6)tothemiddle
position
• Movetheswitch(1)upwardandtotheright
• Pressdowntheignitionbutton(7)tolightup
the open flame
• Whentheunitisworkingasasolderingtool,3
seconds after lighting the torch, please move
the shut off lever (2) to the left and release it.
Thentheopenflamewillbeshutoffandyou
will find the soldering head (4) becomes red.
Shutting off
Movetheswitch(1)upwardsandtotheleft.The
switchwillreturntoOFFposition.
Flame lengt or temperature adjustment
After ignition, turn the flow control knob (6) to the
right to increase the flame length of the torch or
the temperature of soldering tip or hot air, to the
left to decrease the flame length or the
temperature.
Operating tips
• Afterfillingorrefillingwithgas,waitfor
approximately2minutessothatthegasinthe
cylindercanbestable.
• Solderingtipsmustbetin-platedbeforeusing
themforthefirsttime.Athinlayerofsolder
should be applied to the tip when it has been
heated.
• SolderingshouldNOTbecarriedouton“live”
circuits, as this soldering unit does not
possessanyspecialelectricalinsulation
• Keepyoursolderingspongemoist
How to fit or replace different
accessoires
Always allow unit to cool before removing
or replacing tips
Replace soldering tips
• With7mmwrench(15)onthesolderingtipor
hot blow head (9 till 14) and 8 mm wrench on
thesolderinghead(4),youcantightthetipor
hot blow head or unscrew them.
• Whenyouunscrewthenut(3),youcan
remove the guard (8) and soldering head (4).
Now the unit becomes an open flame torch.
Troubleshooting
1. Does not ignite
• Emptygas
• Refill butane gas
• Gas pressure too high or too low
• Slide flow control knob (6) to lower or higher
position
2. Torch flame has no proper power
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm SGM1006 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm SGM1006 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info