562154
5
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
EN
5
14. Bevel angle
15. Handle
16. Cover
17. Saw blade bolt
18. Flange
19. Screw
20. Screw retraction arm
21. Extension pieces (left and right)
22. Lock-button saw blade
23. Angle indicator
24. Support bracket
2. Safety instructions
When using the machine, always carefully follow
the safety precautions supplied and the safety
instructions given below.
Explanation of symbols
Denotes risk of personal injury, loss of
life or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates the presence of an electrical
voltage.
Keep bystanders away.
Wear eye and ear protection.
Wear a dust mask protection
Before each use of the saw
Check the machine. If any part of the machine is
missing, bent or in any other way unusable, or
when an electrical defect occurs, turn the machine
off and take the plug out of the socket. Replace all
missing, damaged or defective parts before using
the machine again.
To fix the saw blade in the slot and to prevent the
piece of work from moving, follow the instructions
below.
• Choose a suitable saw blade for the work.
Use the crosscut saw only for sawing wood
and wood derivatives or light metal such as
aluminium. Other materials can jump away or
get caught in the saw blade or give rise to
other dangers.
• The arrow marked on the saw blade, which
indicates the direction of rotation, must point
in the same direction as the arrow marked on
the machine. The saw blade teeth must point
downwards on the front of the saw.
• Check that the saw blade is sharp,
undamaged and correctly aligned. After
unplugging the machine, push the saw hood
downwards. Rotate the saw blade by hand
and check that it revolves freely. Put the
machine in the 45° position and check free
rotation again. If the blade touches anything it
must be adjusted.
• Keep the saw blade and the clamping surface
for the clamp clean.
• The saw blade flange must always be
mounted with the notch tightened towards the
saw blade.
• Check that all tensioning devices and locks
are secure and that no part has too much play
in it.
• Always press the piece of work firmly against
the stop, so that it cannot tilt or turn while
sawing. No impurities must gather underneath
the piece of work being sawn.
• Make sure that the piece of work cannot move
after being sawn, for example because it is
not completely supported by the surface of
the machine.
• For sawing pieces of work that are not
supported by the full surface, use some
padding or another machine.
• Replace any worn-out table inserts.
• Only use saw blades recommended by the
manufacturer (EN-847-1).
• Never use HS (High Speed) saw blades.
• Check that the sawn off bits can be removed
sideways from the saw blade, otherwise they
can get caught on the blade and flung about.
• Never saw more than one piece of work at the
same time.
• Be extremely careful when sawing large, very
small or awkward pieces of work.
• Be careful when sawing double mitre joints.
• Use additional supports (tables, sheer-legs,
etc) for long pieces of work that can tip over
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-MSM1036

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm MSM1036 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm MSM1036 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Zweeds, Fins als bijlage per email.

De handleiding is 13,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ferm MSM1036

Ferm MSM1036 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Espanõl, Svenska, Suomi - 76 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info